.rs
.\" Troff code generated by TPS Convert from ITU Original Files
.\"                 Not Copyright ( c) 1991 
.\"
.\" Assumes tbl, eqn, MS macros, and lots of luck.
.TA 1c 2c 3c 4c 5c 6c 7c 8c
.ds CH
.ds CF
.EQ
delim @@
.EN
.nr LL 40.5P
.nr ll 40.5P
.nr HM 3P
.nr FM 6P
.nr PO 4P
.nr PD 9p
.po 4P

.rs
\v | 5i'
.LP
\fBMONTAGE: FIN DE L'ANNEXE A EN\(hyT\* | TE DE CETTE PAGE\fR 
.ce 1000
\v'34P'
ANNEX\ B
.ce 0
.ce 1000
(to Recommendation Q.714)
.sp 9p
.RT
.ce 0
.ce 1000
\fBAction tables for the signalling connection\fR 
.sp 1P
.RT
.ce 0
.ce 1000
\fBcontrol part of Signalling System No.\ 7\fR 
.ce 0
.LP
B.1
	\fIIntroduction\fR 
.sp 1P
.RT
.PP
This Annex contains the definitions for the symbols used and
contains the full definition of actions, if any, to be taken on the receipt 
of messages by a signalling point (node). 
.PP
Annex A contains the full definition of states of the signalling
point\ X/Y interface and the transitions between states in the normal
case.
.RT
.sp 1P
.LP
B.2
	\fISymbol definition of the action tables\fR 
.sp 9p
.RT
.PP
The entries given in Table B\(hy1/Q.714 and B\(hy2/Q.714 indicate the
action, if any, to be taken by a SP on receipt of any kind of message, 
and the state the SP enters, which is given in parentheses, following the 
action 
taken.
.bp
.PP
In any state it is possible to receive an Error message (ERR). The
reaction, if any, depends on the contents (error cause and possible
diagnostics) of the message and is specified in\ Q.714, \(sc\ 3.10.3.
.PP
The reaction on messages received with procedure errors (e.g.\ too
long, invalid P(R), not octet aligned,\ etc.) are normal actions and will be
described in the text. So they are covered by the actions indicated as
NORMAL.
.RT
.sp 1P
.LP
B.3
	\fITable of contents\fR 
.sp 9p
.RT
.LP
	Table B\(hy1/Q.714
	Actions taken by SP\(hyY on receipt of
messages.
.LP
	Table B\(hy2/Q.714
	Actions taken by SP\(hyY on receipt of
messages with known message type and containing
mismatch information.
.LP
	Table B\(hy3/Q.714
	Actions taken by SP\(hyY on receipt of
messages during connection establishment and
release phases.
.LP
	Table B\(hy4/Q.714
	Actions taken by SP\(hyY on receipt of messages
during the data transfer phase in a given
state: reset.
.LP
	Table B\(hy5/Q.714
	Actions taken by SP\(hyY on receipt of messages
during the data transfer phase in a given
state: data expedited data, flow control.
.LP
.sp 3
.ce
\fBH.T. [T1.714]\fR 
.ce
TABLE\ B\(hy1/Q.714
.ce
\fBAction taken by SP\(hyY on receipt of messages\fR 
.ps 9
.vs 11
.nr VS 11
.nr PS 9
.TS
center box;
lw(120p) | cw(60p) .
 {
State of the interface as
perceived by node SP\(hyY
Message received by node SP\(hyY
 }	Any state
_
.T&
lw(120p) | lw(60p) .
 {
Any message with unknown message type (see Note)
 }	DISCARD
_
.T&
lw(120p) | lw(60p) .
 {
Any message with known message type and:
 }	 {
See Table B\(hy2/Q.714
a)
unassigned destination local reference
number, or
b)
Originating Point Code received not equal to the PC stored
locally, or
c)
source local reference number received not equal to the remote
local reference number stored locally
 }
_
.T&
lw(120p) | lw(60p) .
Any other message	See Table B\(hy3/Q.714
.TE
.LP
DISCARD:
SP\(hyY discards the received message and takes no subsequent
action.
.LP
\fINote\fR
\ \(em\ This notion of unknown message type depends upon the protocol
class.
.nr PS 9
.RT
.ad r
\fBTABLEAU B\(hy1/Q.714 [T1.714], p. 1\fR 
.sp 1P
.RT
.ad b
.RT
.LP
.rs
.sp 3P
.ad r
Blanc
.ad b
.RT
.LP
.bp
.ce
\fBH.T. [T2.714]\fR 
.ce
TABLE\ B\(hy2/Q.714
.ce
\fBAction taken by SP\(hyY on receipt of messages with known\fR 
.ce

.ce
\fBmessage type and\fR 
.ce
\fBcontaining mismatch information as in Table B\(hy1/Q.714\fR 
.ce
\fBin any state\fR 
.ps 9
.vs 11
.nr VS 11
.nr PS 9
.TS
center box;
lw(60p) | cw(54p) | cw(60p) | cw(54p) .
 {
Type of mismatch
information
Message
received by node PS\(hyY
 }	 {
Unassigned destination local reference number
 }	 {
Source local reference number received not equal to the one stored
locally
 }	 {
Originating Point Code received not equal to the PC stored locally
(see Note\ 1)
 }
_
.T&
cw(60p) | cw(54p) | cw(60p) | cw(54p) .
CR (X)	N.A.	N.A.	N.A.
_
.T&
cw(60p) | cw(54p) | cw(60p) | cw(54p) .
CC (Y, X)	Send ERR (X) (see Note 2)	N.A.	N.A.
_
.T&
cw(60p) | cw(54p) | cw(60p) | cw(54p) .
CREF (Y)	DISCARD	N.A.	N.A.
_
.T&
cw(60p) | cw(54p) | cw(60p) | cw(54p) .
RLSD (Y, X)	Send RLC (X, Y) (see Note 2)	Send ERR (X) (see Note 2)	Send ERR (X) (see Note 2)
_
.T&
cw(60p) | cw(54p) | cw(60p) | cw(54p) .
RLC (Y, X)	DISCARD	DISCARD	DISCARD
_
.T&
cw(60p) | cw(54p) | cw(60p) | cw(54p) .
DT1 (Y)	DISCARD	N.A.	C.O.N.P.
_
.T&
cw(60p) | cw(54p) | cw(60p) | cw(54p) .
DT2 (Y)	DISCARD	N.A.	C.O.N.P.
_
.T&
cw(60p) | cw(54p) | cw(60p) | cw(54p) .
AK (Y)	DISCARD	N.A.	C.O.N.P.
_
.T&
cw(60p) | cw(54p) | cw(60p) | cw(54p) .
ED (Y)	DISCARD	N.A.	C.O.N.P.
_
.T&
cw(60p) | cw(54p) | cw(60p) | cw(54p) .
EA (Y)	DISCARD	N.A.	C.O.N.P.
_
.T&
cw(60p) | cw(54p) | cw(60p) | cw(54p) .
RSR (Y, X)	Send ERR (X)  (see Note 2)	Send ERR (X)  (see Note 2)	Send ERR (X)  (see Note 2)
_
.T&
cw(60p) | cw(54p) | cw(60p) | cw(54p) .
RSC (Y, X)	Send ERR (X)  (see Note 2)	Send ERR (X)  (see Note 2)	Send ERR (X)  (see Note 2)
_
.T&
cw(60p) | cw(54p) | cw(60p) | cw(54p) .
ERR (Y)	For further study	For further study	For further study
_
.T&
cw(60p) | cw(54p) | cw(60p) | cw(54p) .
IT (Y, X)	DISCARD	RELEASE	C.O.N.P
.TE
.LP
DISCARD:
SP\(hyY discards the received message and takes no subsequent
action.
.LP
C.O.N.P.
Check Optionally Not Performed.
.LP
N.A.
Not Applicable
.LP
NAME (d, s):
NAME
= abbreviation of message
.line
d
= destination local reference number
.line
s
= source local reference number.
.LP
\fINote\ 1\fR
\ \(em\ Performing this check is a national option.
.LP
\fINote\ 2\fR
\ \(em\ In this situation no action is taken locally on any existing
connection section. Information in any message sent back is taken from
the received message.
.nr PS 9
.RT
.ad r
\fBTABLEAU B\(hy2/Q.714 [T2.714], p. 2\fR 
.sp 1P
.RT
.ad b
.RT
.LP
.bp
.ce
\fBH.T. [T3.714]\fR 
.ce
TABLE\ B\(hy3/Q.714
.ce
\fBAction taken by SP\(hyY on receipt of messages during connection\fR 
.ce
\fBestablishment and release phases\fR 
.ps 9
.vs 11
.nr VS 11
.nr PS 9
.TS
center box;
lw(48p) | cw(30p) sw(30p) sw(30p) sw(30p) sw(30p) sw(30p) , ^  | c | c | c | c | c | c.
 {
State | f | he | nterface
as perceived by
node SP\(hyY
Message
received
by note SP\(hyY
 }	 {
Signalling connection control ready: r1
 }
	Ready  c1	 {
SP\(hyX
connection pending
c2
 }	 {
SP\(hyY
connection pending
c3
 }	Data  transfer  c4	 {
SP\(hyX
disconnect pending
c5
 }	 {
SP\(hyY
disconnect pending
c6
 }
_
.T&
lw(48p) | cw(30p) | cw(150p) .
Connexion request (CR)	NORMAL (c2)\fR	See Note
_
.T&
lw(48p) | lw(30p) | cw(30p) | cw(30p) | cw(30p) | cw(30p) | cw(30p) .
Connection confirm (CC)		DISCARD  (c2)	NORMAL  (c4)	DISCARD  (c4)	ERROR 1  (c6)	DISCARD  (c6)
_
.T&
lw(48p) | lw(30p) | cw(30p) | cw(30p) | cw(30p) | cw(30p) | cw(30p) .
Connection refused (CREF)		DISCARD  (c2)	NORMAL  (c1)	DISCARD  (c4)	ERROR 1  (c6)	DISCARD  (c6)
_
.T&
lw(48p) | cw(30p) | cw(30p) | cw(30p) | cw(30p) | cw(30p) | cw(30p) .
Released (RLSD)	See Table B\(hy2/Q.714	DISCARD  (c2)	ERROR 2  (c3)	NORMAL  (c5)	DISCARD  (c5)	NORMAL  (c1)
_
.T&
lw(48p) | cw(30p) | cw(30p) | cw(30p) | cw(30p) | cw(30p) | cw(30p) .
Released complete (RLC)		DISCARD  (c2)	ERROR 3  (c1)	DISCARD  (c4)	ERROR 1  (c6)	NORMAL  (c1)
_
.T&
lw(48p) | cw(30p) | cw(30p) | cw(30p) | cw(30p) | cw(30p) | cw(30p) .
Other messages		DISCARD  (c2)	ERROR 3  (c1)	See Table B\(hy4/Q.714	ERROR 1  (c6)	DISCARD
.TE
.LP
(c6)
NORMAL:
The action taken by SP\(hyY follows the normal procedures as defined in the appropriate sections of the procedure text.
.LP
DISCARD:
SP\(hyY discards the received message and takes no subsequent
action.
.LP
ERROR\ 1:
SP\(hyY discards the received message and initiates a connection
release by sending a RLSD message with proper invalid type cause.
.LP
ERROR\ 2:
SP\(hyY returns a Released complete message using information
contained in the message and takes no subsequent action.
.LP
ERROR\ 3:
SP\(hyY discards the received message and releases locally.
.LP
\fINote\fR
\ \(em\ Reception of CR in these states is note possible because CR does
not contain a destination local reference number 
(no\ search is
performed).
.nr PS 9
.RT
.ad r
\fBTABLEAU B\(hy3/Q.714 [T3.714], p. 3\fR 
.sp 1P
.RT
.ad b
.RT
.LP
.rs
.sp 11P
.ad r
Blanc
.ad b
.RT
.LP
.bp
.ce
\fBH.T. [T4.714]\fR 
.ce
TABLE\ B\(hy4/Q.714
.ce
\fBAction taken by node SP\(hyY as receipt of messages during the\fR 
.ce
\fBdata transfer state\fR 
.ps 9
.vs 11
.nr VS 11
.nr PS 9
.TS
center box;
lw(102p) | cw(42p) sw(42p) sw(42p) , ^  | c | c | c.
 {
State of the interface as
perceived by node SP\(hyY
Message received by node SP\(hyY
 }	Data transfer: c4
	Data control  ready  (d1)	SP\(hyX reset  request  (d2)	SP\(hyY reset  request  (d3)
_
.T&
lw(102p) | cw(42p) | cw(42p) | cw(42p) .
 {
Reset request (RSR)
(see Note 2)
 }	NORMAL  (d2)	DISCARD  (d2)	NORMAL  (d1)
_
.T&
lw(102p) | cw(42p) | cw(42p) | cw(42p) .
 {
Reset confirmation (RSC)
(see Note 2)
 }	ERROR  (d3)	ERROR  (d3)	NORMAL  (d1)
_
.T&
lw(102p) | cw(42p) | cw(42p) | cw(42p) .
Other messages	See  Table B\(hy5/Q.714	ERROR  (d3)  (see Note 1)	DISCARD
.TE
.LP
(d3)
NORMAL:
The action taken by SP\(hyY follows the normal procedures as defined in the appropriate sections of the procedure text.
.LP
DISCARD:
Signalling point Y discards the received message and takes no
subsequent action.
.LP
ERROR:
Signalling point Y discards the received message and initiates a
reset by transmitting a reset request message with the appropriate cause
indication.
.LP
\fINote\ 1\fR
\ \(em\ If signalling point Y issues a reset by transmitting a reset
request message as a result of an error condition in state\ d2, it should
eventually consider the interface to be in the Data control ready
state\ (d1).
.LP
\fINote\ 2\fR
\ \(em\ Reception of these messages for a class 2 connection section may
trigger the sending of an ERR message back if these message types are known
by the receiving SCCP.
.nr PS 9
.RT
.ad r
\fBTABLEAU B\(hy4/Q.714 [T4.714], p. 4\fR 
.ad b
.RT
.ce
\fBH.T. [T5.714]\fR 
.ce
TABLE\ B\(hy5/Q.714
.ce
\fBAction taken by SP\(hyY on receipt of messages during the data\fR 
.ce
\fBcontrol ready state\fR 
.ps 9
.vs 11
.nr VS 11
.nr PS 9
.TS
center box;
lw(84p) | cw(36p) sw(36p) sw(36p) sw(36p) , ^  | c | c | c | c.
 {
State of the interface as
perceived by node SP\(hyY
Message received by node SP\(hyY
 }	Data control ready: d1
	Normal data flow  e1	SP\(hyX expedited data  e2	SP\(hyY expedited data  e3	 {
SP\(hyX and SP\(hyY expedited data
e4
 }
_
.T&
lw(84p) | cw(36p) | cw(36p) | cw(36p) | cw(36p) .
Expedited data (ED)	NORMAL  (d2)	ERROR  (d3)	NORMAL  (d4)	ERROR  (d3)
_
.T&
lw(84p) | cw(36p) | cw(36p) | cw(36p) | cw(36p) .
 {
Expedited data (EA) acknowledgement
 }	DISCARD  (e1)	DISCARD  (e2)	NORMAL  (e1)	NORMAL  (e2)
_
.T&
lw(84p) | cw(36p) | cw(36p) | cw(36p) | cw(36p) .
 {
Data (DT), data acknowledgement (AK) and Inactivity Test (IT)
 }	NORMAL  (e1)	NORMAL  (e2)	NORMAL  (e3)	NORMAL
.TE
.LP
(e4)
NORMAL:
The action taken by signalling point Y follows the normal
procedures as defined in the appropriate sections of the procedure text.
.LP
DISCARD:
Signalling point Y discards the received message and takes no
subsequent action as direct result of receiving that message.
.LP
ERROR:
Signalling point Y discards the received message packet and
indicates a reset by transmitting a reset request message with the appropriate cause indication (e.g.\ procedure error).
.LP
\fINote\fR
\ \(em\ Reception of an ED, EA, DT
2 or AK message for a class 2 connection section will cause the receiving SCCP to DISCARD any of these messages. A
DT
1 message received for a class\ 3 connection section will also be
discarded.
.nr PS 9
.RT
.ad r
\fBTABLEAU B\(hy5/Q.714 [T5.714], p. 5\fR 
.ad b
.RT
.LP
.bp
.ce 1000
ANNEX\ C
.ce 0
.ce 1000
(to Recommendation Q.714)
.sp 9p
.RT
.ce 0
.ce 1000
\fBState transition diagrams (STD)\fR 
.sp 1P
.RT
.ce 0
.ce 1000
\fBfor the signalling connection \fBcontrol part of\fR 
.ce 0
.ce 1000
\fBSignalling System No.\ 7\fR 
.ce 0
.LP
C.1
	\fIGeneral\fR 
.sp 1P
.RT
.PP
This annex contains the description of the main SCCP functions
(except SCCP management (SCMG) which is contained in annex\ D to
Recommendation\ Q.714) according to the CCITT Specification and Description
Language\ (SDL).
.PP
For the SCCP as a whole, Figure 1/Q.714 illustrates a subdivision into 
functional blocks, showing their functional interactions as well as the 
functional interactions with the other major functions of signalling
system\ No.\ 7 (e.g.\ MTP).
.PP
The functional breakdown shown in this diagram is intended to
illustrate a reference model, and to assist interpretation of the text 
of the SCCP procedures. The state transition diagrams are intended to show 
precisely the behaviour of the signalling system under normal and abnormal 
conditions as viewed from a remote location. It must be emphasized that 
the functional 
partitioning shown in the following diagrams is used only to facilitate
understanding of the system behaviour, and is not intended to specify the
functional partitioning to be adopted in a practical implementation of the
signalling system.
.RT
.sp 1P
.LP
C.2
	\fIDrafting conventions\fR 
.sp 9p
.RT
.PP
Each major function is designated by its acronym (e.g.\ SCOC\ =\ SCCP connection\(hyoriented 
control). 
.PP
External inputs and outputs are used for interactions between
different functional blocks. Included within each input and output symbol
in the state transition diagrams are acronyms which identify the
functional blocks which are the source and the destination of the
message,\ e.g.:
.RT
.LP
	SCRC\ \(ra\ SCOC
	indicates that the message is sent from SCCP
routing control to SSCP connection\(hyoriented
control
.PP
Internal inputs and outputs are only used to indicate control of   timers.
.sp 1P
.LP
C.3
	\fIFigures\fR 
.sp 9p
.RT
.PP
The list of figures is as follows:
.RT
.LP
	Figure\ C\(hy1/Q.714
	SCCP routing control procedures (SCRC).
.LP
	Figure\ C\(hy2/Q.714
	Connection establishment and release
procedures at originating node for SCCP
connection\(hyoriented control (SCOC).
(Sheets\ 1 to 3: connection establishment,
and sheets\ 4 to\ 6: connection release
procedures)
.LP
	Figure\ C\(hy3/Q.714
	Connection establishment and release
procedures at destination node for SCCP
connection\(hyoriented control (SCOC).
(Sheets\ 1 to 2: connection establishment,
and sheets\ 3 to\ 5: connection release
procedures)
.LP
	Figure\ C\(hy4/Q.714
	Data transfer procedures at originating and
destination nodes for SCCP connection\(hyoriented
control (SCOC).
.LP
	Figure\ C\(hy5/Q.714
	Expedited data transfer procedures at
originating and destination nodes for SCCP
connection\(hyoriented control (SCOC).
.LP
	Figure\ C\(hy6/Q.714
	Reset procedures at originating and
destination nodes for SCCP connection\(hyoriented
control (SCOC).
.LP
	Figure\ C\(hy7/Q.714
	Connection establishment and release
procedures at intermediate node for SCCP
connection\(hyoriented control (SCOC).
(Sheets\ 1 to 4: connection establishment, and
sheets\ 5 to\ 9: connection release
procedures)
.LP
	Figure\ C\(hy8/Q.714
	Data transfer procedures at intermediate node
for SCCP connection\(hyoriented control
(SCOC).
.bp
.LP
	Figure\ C\(hy9/Q.714
	Expedited data transfer procedures at
intermediate node for SCCP connection\(hyoriented
control (SCOC).
.LP
	Figure\ C\(hy10/Q.714
	Reset procedures at intermediate node for
SCCP connection\(hyoriented control (SCOC).
.LP
	Figure\ C\(hy11/Q.714
	Restart procedure for SCCP
connection\(hyoriented control (SCOC).
.LP
	Figure\ C\(hy12/Q.714
	SCCP connectionless control (SCLC).
.sp 1P
.LP
C.4
	\fIAbbreviations and timers\fR 
.sp 9p
.RT
.PP
Abbreviations and timers used in Figures\ C\(hy1/Q.714 to C\(hy11/Q.714
are listed below.
.RT
.sp 1P
.LP
	\fIAbbreviations\fR 
.sp 9p
.RT
.LP
	CR
	Connection Request
.LP
	DPC 
	Destination Point Code
.LP
	GT
	Global Title
.LP
	IT
	Inactivity Test
.LP
	MSG 
	Message
.LP
	MTP 
	Message Transfer Part
.LP
	NPDU
	Network Protocol Data Unit
.LP
	NSDU
	Network Service Data Unit
.LP
	PC
	Point Code
.LP
	SCCP
	Signalling Connection Control Part
.LP
	SCLC
	SCCP Connectionless Control
.LP
	SCMG
	SCCP Management
.LP
	SCOC
	SCCP Connection\(hyOriented Control
.LP
	SCRC
	SCCP Routing Control
.LP
	SLS 
	Signalling Link Selection
.LP
	SS
	Sub\(hySystem
.LP
	SSN 
	Sub\(hySystem Number
.LP
	SSPC
	Sub\(hySystem Prohibited Control
.sp 1P
.LP
	\fITimers\fR 
.sp 9p
.RT
.LP
	T(conn est)
	Waiting for connection confirm message.
.LP
	T(ias)
	Delay to send a message on a connection section.
.LP
	T(iar)
	Waiting to receive a message on a connection
section.
.LP
	T(rel)
	Waiting for release complete message.
.LP
	T(int)
	Waiting to report abnormal release to maintenance
function.
.LP
	T(guard)
	Waiting to resume normal procedures for temporary
connection sections during the restart
procedure
.LP
.rs
.sp 6P
.ad r
Blanc
.ad b
.RT
.LP
.bp
.LP
.rs
.sp 47P
.ad r
\fBFigure C\(hy1/Q.714 (feuillet 1 sur 3), (N), p. 6\fR 
.sp 1P
.RT
.ad b
.RT
.LP
.bp
.LP
.rs
.sp 47P
.ad r
\fBFigure C\(hy1/Q.714 (feuillet 2 sur 3), (N), p. 7\fR 
.sp 1P
.RT
.ad b
.RT
.LP
.bp
.LP
.rs
.sp 47P
.ad r
\fBFigure C\(hy1/Q.714 (feuillet 3 sur 3), (N), p. 8\fR 
.sp 1P
.RT
.ad b
.RT
.LP
.bp
.LP
.rs
.sp 47P
.ad r
\fBFigure C\(hy2/Q.714 (feuillet 1 sur 6), (N), p. 9\fR 
.sp 1P
.RT
.ad b
.RT
.LP
.bp
.LP
.rs
.sp 47P
.ad r
\fBFigure C\(hy2/Q.714 (feuillet 2 sur 6), (N), p. 10\fR 
.sp 1P
.RT
.ad b
.RT
.LP
.bp
.LP
.rs
.sp 47P
.ad r
\fBFigure C\(hy2/Q.714 (feuillet 3 sur 6), (N), p. 11\fR 
.sp 1P
.RT
.ad b
.RT
.LP
.bp
.LP
.rs
.sp 47P
.ad r
\fBFigure C\(hy2/Q.714 (feuillet 4 sur 6), (N), p. 12\fR 
.sp 1P
.RT
.ad b
.RT
.LP
.bp
.LP
.rs
.sp 47P
.ad r
\fBFigure C\(hy2/Q.714 (feuillet 5 sur 6), (N), p. 13\fR 
.sp 1P
.RT
.ad b
.RT
.LP
.bp
.LP
.rs
.sp 47P
.ad r
\fBFigure C\(hy2/Q.714 (feuillet 6 sur 6), (N), p. 14\fR 
.sp 1P
.RT
.ad b
.RT
.LP
.bp
.LP
.rs
.sp 47P
.ad r
\fBFigure C\(hy3/Q.714 (feuillet 1 sur 5), (N), p. 15\fR 
.sp 1P
.RT
.ad b
.RT
.LP
.bp
.LP
.rs
.sp 47P
.ad r
\fBFigure C\(hy3/Q.714 (feuillet 2 sur 5), (N), p. 16\fR 
.sp 1P
.RT
.ad b
.RT
.LP
.bp
.LP
.rs
.sp 47P
.ad r
\fBFigure C\(hy3/Q.714 (feuillet 3 sur 5), (N), p. 17\fR 
.sp 1P
.RT
.ad b
.RT
.LP
.bp
.LP
.rs
.sp 47P
.ad r
\fBFigure C\(hy3/Q.714 (feuillet 4 sur 5), (N), p. 18\fR 
.sp 1P
.RT
.ad b
.RT
.LP
.bp
.LP
.rs
.sp 47P
.ad r
\fBFigure C\(hy3/Q.714 (feuillet 5 sur 5), (N), p. 19\fR 
.sp 1P
.RT
.ad b
.RT
.LP
.bp
.LP
.rs
.sp 47P
.ad r
\fBFigure C\(hy4/Q.714 (feuillet 1 sur 4), (N), p. 20\fR 
.sp 1P
.RT
.ad b
.RT
.LP
.bp
.LP
.rs
.sp 47P
.ad r
\fBFigure C\(hy4/Q.714 (feuillet 2 sur 4), (N), p. 21\fR 
.sp 1P
.RT
.ad b
.RT
.LP
.bp
.LP
.rs
.sp 47P
.ad r
\fBFigure C\(hy4/Q.714 (feuillet 3 sur 4), (N), p. 22\fR 
.sp 1P
.RT
.ad b
.RT
.LP
.bp
.LP
.rs
.sp 47P
.ad r
\fBFigure C\(hy4/Q.714 (feuillet 4 sur 4), (N), p. 23\fR 
.sp 1P
.RT
.ad b
.RT
.LP
.bp
.LP
.rs
.sp 47P
.ad r
\fBFigure C\(hy5/Q.714, (N), p. 24\fR 
.sp 1P
.RT
.ad b
.RT
.LP
.bp
.LP
.rs
.sp 47P
.ad r
\fBFigure C\(hy6/Q.714 (feuillet 1 sur 4), (N), p. 25\fR 
.sp 1P
.RT
.ad b
.RT
.LP
.bp
.LP
.rs
.sp 47P
.ad r
\fBFigure C\(hy6/Q.714 (feuillet 2 sur 4), (N), p. 26\fR 
.sp 1P
.RT
.ad b
.RT
.LP
.bp
.LP
.rs
.sp 47P
.ad r
\fBFigure C\(hy6/Q.714 (feuillet 3 sur 4), (N), p. 27\fR 
.sp 1P
.RT
.ad b
.RT
.LP
.bp
.LP
.rs
.sp 47P
.ad r
\fBFigure C\(hy6/Q.714 (feuillet 4 sur 4), (N), p. 28\fR 
.sp 1P
.RT
.ad b
.RT
.LP
.bp
.LP
.rs
.sp 47P
.ad r
\fBFigure C\(hy7/Q.714 (feuillet 1 sur 9), (N), p. 29\fR 
.sp 1P
.RT
.ad b
.RT
.LP
.bp
.LP
.rs
.sp 47P
.ad r
\fBFigure C\(hy7/Q.714 (feuillet 2 sur 9), (N), p. 30\fR 
.sp 1P
.RT
.ad b
.RT
.LP
.bp
.LP
.rs
.sp 47P
.ad r
\fBFigure C\(hy7/Q.714 (feuillet 3 sur 9), (N), p. 31\fR 
.sp 1P
.RT
.ad b
.RT
.LP
.bp
.LP
.rs
.sp 47P
.ad r
\fBFigure C\(hy7/Q.714 (feuillet 4 sur 9), (N), p. 32\fR 
.sp 1P
.RT
.ad b
.RT
.LP
.bp
.LP
.rs
.sp 47P
.ad r
\fBFigure C\(hy7/Q.714 (feuillet 5 sur 9), (N), p. 33\fR 
.sp 1P
.RT
.ad b
.RT
.LP
.bp
.LP
.rs
.sp 47P
.ad r
\fBFigure C\(hy7/Q.714 (feuillet 6 sur 9), (N), p. 34\fR 
.sp 1P
.RT
.ad b
.RT
.LP
.bp
.LP
.rs
.sp 47P
.ad r
\fBFigure C\(hy7/Q.714 (feuillet 7 sur 9), (N), p. 35\fR 
.sp 1P
.RT
.ad b
.RT
.LP
.bp
.LP
.rs
.sp 47P
.ad r
\fBFigure C\(hy7/Q.714 (feuillet 8 sur 9), (N), p. 36\fR 
.sp 1P
.RT
.ad b
.RT
.LP
.bp
.LP
.rs
.sp 47P
.ad r
\fBFigure C\(hy7/Q.714 (feuillet 9 sur 9), (N), p. 37\fR 
.sp 1P
.RT
.ad b
.RT
.LP
.bp