.rs .\" Troff code generated by TPS Convert from ITU Original Files .\" Not Copyright ( c) 1991 .\" .\" Assumes tbl, eqn, MS macros, and lots of luck. .TA 1c 2c 3c 4c 5c 6c 7c 8c .ds CH .ds CF .EQ delim @@ .EN .nr LL 40.5P .nr ll 40.5P .nr HM 3P .nr FM 6P .nr PO 4P .nr PD 9p .po 4P .rs \v | 5i' .sp 1P .ce 1000 \v'3P' SECTION\ 4 .ce 0 .sp 1P .ce 1000 \fBCHARACTERISTICS\ OF\ \fR \fBEQUIPMENTS\ FOR\ CODING\ ANALOGUE\fR .ce 0 .sp 1P .ce 1000 \fBSOUND\ PROGRAMME\ SIGNALS\fR .ce 0 .sp 1P .sp 2P .LP \fBRecommendation\ J.41\fR .EF '% Fascicle\ III.6\ \(em\ Rec.\ J.41'' .OF '''Fascicle\ III.6\ \(em\ Rec.\ J.41 %' .RT .sp 2P .ce 1000 \fBCHARACTERISTICS\ OF\ \fBEQUIPMENT\ FOR\ THE\ CODING\ OF\ ANALOGUE\fR .ce 0 .ce 1000 \fBHIGH\ QUALITY\ SOUND\ PROGRAMME\ SIGNALS\ FOR\ TRANSMISSION\fR .ce 0 .sp 1P .ce 1000 \fBON\ 384\ kbit/s\ CHANNELS\fR .ce 0 .sp 1P .ce 1000 \fI(Malaga\(hyTorremolinos, 1984; amended at Melbourne, 1988)\fR .sp 9p .RT .ce 0 .sp 1P .LP \fB1\fR \fBGeneral\fR .sp 1P .RT .PP 1.1 This Recommendation gives the characteristics of equipment for the coding of 15\ kHz monophonic analogue sound\(hyprogramme signals into a digital signal of 384\ kbit/s. For stereophonic operation, two monophonic digital codecs can be utilized. Two monophonic digital signals that form a stereophonic signal should be routed together over the same transmission systems (path) to avoid any difference in transmission delay. .sp 9p .RT .PP 1.2 Equipment for coding of analogue sound\(hyprogramme signals, as specified in this Recommendation, can be: .sp 9p .RT .LP a) A stand\(hyalone encoder/decoder with a digital interface at 384\ kbit/s. The encoder operation and the decoder operation may be performed in two separate equipments or in the same equipment. .LP b) A combined encoder\(hymultiplex/decoder\(hydemultiplex with a digital interface at\ 1544 or 2048\ kbit/s. The encoder\(hymultiplex operation and the decoder\(hydemultiplex operation may be performed in two separate equipments or in the same equipment. .PP In case b), it is not mandatory to provide an external digital sound programme access port at 384\ kbit/s. .PP 1.3 Two methods of encoding have been specified by the CMTT\ [1] and these form the basis for this Recommendation. .sp 9p .RT .sp 2P .LP \fB2\fR \fBTransmission performance\fR .sp 1P .RT .PP The transmission performance per encoder/decoder pair shall be such that the limits specified in Recommendation\ J.21 (CCIR Recommendation\ 505) are not exceeded by three encoder/decoder pairs connected in tandem at audio frequencies. .PP \fINote\fR \ \(em\ When transmitting stereophonic sound programme signals, it is necessary that the encoder and decoder are designed such that they will meet the specified requirements for phase difference. .PP In order to avoid any unnecessary complexity, the sampling of channels\ A and\ B should be performed simultaneously. .bp .RT .sp 2P .LP \fB3\fR \fBMethod of encoding\fR .sp 1P .RT .PP 3.1 The recommended encoding laws are as specified in [1]. .sp 9p .RT .PP 3.2 These encoding laws are based on a uniformly quantized 14\(hybit per sample PCM technique with companding and employ either: .sp 9p .RT .LP a) eleven\(hysegment 14\(hy to 11\(hybit instantaneous A\(hylaw companding, or .LP b) five\(hyrange 14\(hy to 10\(hybit near instantaneous companding. .PP For provisional rules for through connection between the two companding methods, see Note\ 4 in\ [1]. .PP 3.3 Other coding techniques which may be used by bilateral agreement of the Administrations concerned are also listed in Annex\ A. However, these techniques do not form part of this Recommendation. .sp 9p .RT .PP 3.4 Equipment characteristics common to both methods of encoding are: .sp 9p .RT .LP Nominal audio bandwidth: 0.04 to 15 kHz. Audio interface: see Recommendation J.21, \(sc\ 2. Sampling frequency (CCIR Recommendation 606): 32 (1\ \(+-\ 5\ \(mu\ 10\uD\dlF261\u5\d) kHz. Pre/de\(hyemphasis: Recommendation J.17 with 6.5\ dB attenuation at 800\ Hz. .PP \fINote\fR \ \(em\ Pre\(hyemphasis and de\(hyemphasis are not used by the Administrations of Canada, Japan and the United States on their national circuits and on international circuits between each other, but are used on international circuits to other countries. .sp 2P .LP \fB4\fR \fBEquipment using \fR \fBinstantaneous companding\fR .sp 1P .RT .sp 1P .LP 4.1 \fICoding table\fR \v'3p' .sp 9p .RT .PP 4.1.1 The coding law is specified in Table\ 1/J.41. .PP 4.1.2 The allocation of character signals (PCM code words) is also given in Table\ 1/J.41. Two variants (A\ and\ B) of character signals are allowed. .sp 9p .RT .PP \fINote\fR \ \(em\ In the case of digital interconnection between variants\ A and\ B, the conversion from one set of character signals to the other in Table\ 1/J.41 can be implemented without any performance degradation. In the case of analogue interconnection, a small reduction in the S/N\ ratio, in the order of 3\ dB, is expected. .sp 1P .LP 4.2 \fIBit rates\fR \v'3p' .sp 9p .RT .LP Nominal source coding bit rate (32 kHz\ \(mu\ 11 bits/sample) 352\ kbit/s Error protection \ 32\ kbit/s Transmission bit rate 384\ kbit/s .sp 1P .LP 4.3 \fIOverload level\fR .sp 9p .RT .PP The overload level for a sine\(hywave signal at zero\ dB insertion loss frequency (2.1\ kHz) of the pre\(hyemphasis is +15\ dBm0s. .RT .sp 1P .LP 4.4 \fIDigital signal format\fR .sp 9p .RT .PP The character signal bit sequences for variants A and B are shown in Figure\ 1/J.41. .RT .sp 1P .LP 4.5 \fIBit error protection\fR .sp 9p .RT .PP One parity bit is added to each 11\(hybit character signal. .bp .RT .ce \fBH.T. [T1.41]\fR .ps 9 .vs 11 .nr VS 11 .nr PS 9 .TS center box; cw(342p) . TABLE\ 1/J.41 .T& cw(342p) . { \fB11 segment, 14 to 11 bit instantaneous companding A\(hylaw\fR \fBPCM for sound\(hyprogramme signals (positive half only) | fR\(ua\fBa\fR\(ua\fB)\fR } .T& lw(180p) | cw(162p) . { 11 bit coding Allocation of character signals } .TE .TS center box ; cw(42p) | cw(36p) | cw(36p) | cw(24p) | cw(30p) | cw(12p) | cw(72p) | cw(18p) | lw(72p) . Normalized analogue input Normalized analogue output Compressed digital code Segment No. Effective resolution (bits) . 1 { Variant A | ua\d\u)\d 2\ 3\ 4\ \ \ 5\ 6\ 7\ 8\ 9\ 10\ \ \ 11 } . S { Variant B | ub\d\u)\d X Y Z A B C D E F G } _ .T& cw(42p) | cw(36p) | cw(36p) | cw(24p) | cw(30p) | cw(12p) | cw(72p) | cw(18p) | lw(72p) . 8160 to 8192 8176\fB.\ \fR 895 { \ \ \ \ \ \ \ \ 1\ 1\ 1\ 1\ 1\ 1\ \ \ 1 } 1 1 1 1 1 1 1 .T& cw(42p) | cw(36p) | cw(36p) | cw(24p) | cw(30p) | cw(12p) | cw(72p) | cw(18p) | lw(72p) . 1 \ 9 0 { 1\ 1\ 1\ \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ } 0 1 1 0 .T& cw(42p) | cw(36p) | cw(36p) | cw(24p) | cw(30p) | cw(12p) | cw(72p) | cw(18p) | lw(72p) . 4096 to 4128 4112\fB.\ \fR 768 { \ \ \ \ \ \ \ \ 0\ 0\ 0\ 0\ 0\ 0\ \ \ 0 } 0 0 0 0 0 0 0 _ .T& cw(42p) | cw(36p) | cw(36p) | cw(24p) | cw(30p) | cw(12p) | cw(72p) | cw(18p) | lw(72p) . 4080 to 4096 4088\fB.\ \fR 767 { \ \ \ \ \ \ \ \ 1\ 1\ 1\ 1\ 1\ 1\ \ \ 1 } 1 1 1 1 1 1 1 .T& cw(42p) | cw(36p) | cw(36p) | cw(24p) | cw(30p) | cw(12p) | cw(72p) | cw(18p) | lw(72p) . 2 10 0 { 1\ 1\ 0\ \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ } 0 1 0 1 .T& cw(42p) | cw(36p) | cw(36p) | cw(24p) | cw(30p) | cw(12p) | cw(72p) | cw(18p) | lw(72p) . 2048 to 2064 2056\fB.\ \fR 640 { \ \ \ \ \ \ \ \ 0\ 0\ 0\ 0\ 0\ 0\ \ \ 0 } 0 0 0 0 0 0 0 _ .T& cw(42p) | cw(36p) | cw(36p) | cw(24p) | cw(30p) | cw(12p) | cw(72p) | cw(18p) | lw(72p) . 2040 to 2048 2044\fB.\ \fR 639 { \ \ \ \ \ \ \ \ 1\ 1\ 1\ 1\ 1\ 1\ \ \ 1 } 1 1 1 1 1 1 1 .T& cw(42p) | cw(36p) | cw(36p) | cw(24p) | cw(30p) | cw(12p) | cw(72p) | cw(18p) | lw(72p) . 3 11 0 { 1\ 0\ 1\ \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ } 0 1 0 0 .T& cw(42p) | cw(36p) | cw(36p) | cw(24p) | cw(30p) | cw(12p) | cw(72p) | cw(18p) | lw(72p) . 1024 to 1032 1028\fB.\ \fR 512 { \ \ \ \ \ \ \ \ 0\ 0\ 0\ 0\ 0\ 0\ \ \ 0 } 0 0 0 0 0 0 0 _ .T& cw(42p) | cw(36p) | cw(36p) | cw(24p) | cw(30p) | cw(12p) | cw(72p) | cw(18p) | lw(72p) . 1020 to 1024 1022\fB.\ \fR 511 { \ \ \ \ \ \ \ \ 1\ 1\ 1\ 1\ 1\ 1\ \ \ 1 } 1 1 1 1 1 1 1 .T& cw(42p) | cw(36p) | cw(36p) | cw(24p) | cw(30p) | cw(12p) | cw(72p) | cw(18p) | lw(72p) . 4 12 0 { 1\ 0\ 0\ \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ } 0 0 1 1 .T& cw(42p) | cw(36p) | cw(36p) | cw(24p) | cw(30p) | cw(12p) | cw(72p) | cw(18p) | lw(72p) . \ 512 to \ 516 \ 514\fB.\ \fR 384 { \ \ \ \ \ \ \ \ 0\ 0\ 0\ 0\ 0\ 0\ \ \ 0 } 0 0 0 0 0 0 0 _ .T& cw(42p) | cw(36p) | cw(36p) | cw(24p) | cw(30p) | cw(12p) | cw(72p) | cw(18p) | lw(72p) . \ 510 to \ 512 \ 511\fB.\ \fR 383 { \ \ \ \ \ \ \ \ 1\ 1\ 1\ 1\ 1\ 1\ \ \ 1 } 1 1 1 1 1 1 1 .T& cw(42p) | cw(36p) | cw(36p) | cw(24p) | cw(30p) | cw(12p) | cw(72p) | cw(18p) | lw(72p) . 5 13 0 { 0\ 1\ 1\ \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ } 0 0 1 0 .T& cw(42p) | cw(36p) | cw(36p) | cw(24p) | cw(30p) | cw(12p) | cw(72p) | cw(18p) | lw(72p) . \ 256 to \ 258 \ 257\fB.\ \fR 256 { \ \ \ \ \ \ \ \ 0\ 0\ 0\ 0\ 0\ 0\ \ \ 0 } 0 0 0 0 0 0 0 _ .TE .nr PS 9 .RT .ad r \fBTableau 1/J.41 [T1.41] \ \ (\*`a l'italienne), p.\fR .sp 1P .RT .ad b .RT .LP .bp .sp 1P .LP 4.5.1 \fIVariant A\fR .sp 9p .RT .PP The five most significant bits of each sample are protected against errors by means of a parity bit. In the converter of the transmitting part, the parity bit is added as the 12th\ bit to each code word. Its value is fixed so that the\ 6\ bit parity block always contains only an odd number of \*Qone\*U values. In order that even bit error structures can also result in parity violations, the protected and unprotected bits of each code word are interleaved in ascending and descending sequence, as shown in Figure\ 1/J.41. .RT .LP .rs .sp 28P .ad r \fBFigure 1/J.41, p.\fR .sp 1P .RT .ad b .RT .sp 1P .LP 4.5.2 \fIVariant B\fR .sp 9p .RT .PP The added parity bit shall be based on the 7 most significant bits of the 11\(hybit PCM word. These are bits\ S, X, Y, Z, A, B,\ C. The parity of \*Qones\*U bit shall be \fIeven\fR . Since the chord bits (X, Y,\ Z) always contain a one, the minimum number of ones per sample is\ 2, resulting in a minimum ones density of\ 1/6. .RT .sp 1P .LP 4.5.3 \fIError concealment\fR .sp 9p .RT .PP If a parity violation is detected, an error concealment technique should be applied (for instance, replacement by interpolation, extrapolation or repetition. For multiple parity violation (error bursts), a muting technique should be applied. .bp .RT .sp 1P .LP 4.6 \fIDigital interface at 384 kbit/s\fR .sp 9p .RT .PP Under study (see Recommendations G.735 and G.737). .RT .sp 1P .LP 4.7 \fISynchronization\fR .sp 9p .RT .PP The coding equipment operates in synchronism with the clock of subsequent multiplex equipment or the network clock. In cases where the digital interface is provided, bit and byte (24\ bit, as shown in Figure\ 1/J.41) timing information is required. .PP Variant A: A solution for synchronous access is given in Recommandations\ G.735 and\ G.737. .PP Variant B: The solution for synchronous access is under study. .RT .sp 2P .LP 4.8 \fIFault condition and consequent actions\fR .sp 1P .RT .sp 1P .LP 4.8.1 \fIVariant A\fR .sp 9p .RT .PP Where a 384 kbit/s digital interface is provided, the same principles for fault conditions and subsequent actions as those outlined in Recommendation\ G.732 should be followed. .RT .sp 1P .LP 4.8.2 \fIVariant B\fR .sp 9p .RT .PP Under study. .RT .sp 2P .LP \fB5\fR \fBEquipment using \fR \fBnear\(hyinstantaneous companding\fR .sp 1P .RT .sp 1P .LP 5.1 \fIIntroduction\fR .sp 9p .RT .PP The equipment described in this section uses the near\(hyinstantaneous method of companding in the coding of high quality sound\(hyprogramme signals into digital form. .PP A two\(hystage process is used in the encoding equipment: .RT .LP a) Conversion of a 15 kHz channel into a 338 kbit/s stream. .LP \fINote\fR \ \(em\ The value of 338 kbit/s has been chosen to allow for the possible multiplexing of 6\ channels into a 2048\ kbit/s dedicated frame format. .LP b) Asynchronous insertion of the 338 kbit/s stream into a 384\ kbit/s stream. .LP \fINote\fR \ \(em\ The asynchronous insertion of the 338 kbit/s stream into a 384\ kbit/s stream allows the use, at the encoder location, of a clock not necessarily synchronous to the network clock. It can be advantageous when the encoder equipment and the insertion equipment (see Recommendations\ G.735 and\ G.737) are located in different places, and when the transmission link between them is unidirectional, .LP and the reverse processes in the decoding equipment. .sp 2P .LP 5.2 \fIConversion from 15 kHz to 338 kbit/s\fR .sp 1P .RT .sp 1P .LP 5.2.1 \fIOverload level\fR .sp 9p .RT .PP The overload level for a sine\(hywave signal at the zero dB insertion loss frequency (2.1\ kHz) of the pre\(hyemphasis circuit, is +12\ dBm0s. .RT .sp 1P .LP 5.2.2 \fICompanding\fR .sp 9p .RT .PP Near\(hyinstantaneous companding is used to achieve a data rate reduction from 14\ bits/sample to 10\ bits/sample. The system codes a block of 32\ samples into one of 5\ gain ranges, according to the highest value sample in the block. The companding characteristic is shown diagramatically in Figure\ 2/J.41 and the parameters are specified in Table\ 2/J.41. .bp .RT .LP .rs .sp 31P .ad r \fBFigure 2/J.41, p.\fR .sp 1P .RT .ad b .RT .sp 1P .LP 5.2.3 \fIRange coding and protection\fR .sp 9p .RT .PP Information defining the range used is transmitted over 3\ successive blocks as a\ 7\(hybit word, increasing to\ 11\ bits in a Hamming\ 7, 11 single error correcting code and distributed throughout the 3\ blocks as follows: .RT .LP The five possible values for each of the 3 range co des (one range code for each block in the 3\ ms frame; see Figure\ 3/J.41), are: .LP Range 4\ \ highest signal level .LP Range 3 .LP Range 2 .LP Range 1 .LP Range 0\ \ lowest signal level .LP Range codes generated in this way from three successive blo cks are designated Ra, Rb and\ Rc. They are then used to compute a single\ 7\(hybit range code, R, as follows: .sp 1P .ce 1000 R\ =\ 25Ra\ +\ 5Rb\ +\ Rc\ +\ 1 .ce 0 .sp 1P .LP R1 to R7 form the unsigned binary representation of t his code which is transmitted LSB first (R1 to\ R7), followed by 4 protection bits R8 to\ R11 made up as follows: .LP \ R8\ =\ ( R7+R6+R5+R4+ R3+R2+R1) MOD 2 .LP \ R9\ =\ ( R7+ R6+R5+R4 +R3+R2+R1 ) MOD 2 .LP R10\ =\ (R7 +R6 +R5+R4 +R3 +R2+R1) MOD 2 .LP R11\ =\ (R7+R6 +R5 +R4+R3 +R2 +R1) MOD 2 .bp .ce \fBH.T. [T2.41]\fR .ce TABLE\ 2/J.41 .ce \fBCompanding law \(em Two's complement coding\fR .ps 9 .vs 11 .nr VS 11 .nr PS 9 .TS center box; cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . Range Normalized analogue input Normalized analogue output { Compressed digital code MSB LSB } Effective Resolution _ .T& cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . 4 +8176 to +8192 +8184 | +511\ \ (0111111111) 10 bits .T& cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ \ \ \ 0 to \ \ +16 \ \ \ +8 | \ \ \ 0\ \ (0000000000) .T& cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ \ \(em16 to \ \ \ \ 0 \ \ \ \(em8 | \ \ \(em1\ \ (1111111111) .T& cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \(em8192 to \(em8176 \(em8184 | \(em512\ \ (1000000000) _ .T& cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . 3 +4088 to +4096 +4092 | +511\ \ (0111111111) 11 bits .T& cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ \ \ \ 0 to \ \ \ +8 \ \ \ +4 | \ \ \ 0\ \ (0000000000) .T& cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ \ \ \(em8 to \ \ \ \ 0 \ \ \ \(em4 | \ \ \(em1\ \ (1111111111) .T& cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \(em4096 to \(em4088 \(em4092 | \(em512\ \ (1000000000) _ .T& cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . 2 +2044 to +2048 +2046 | +511\ \ (0111111111) 12 bits .T& cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ \ \ \ 0 to \ \ \ +4 \ \ \ +2 | \ \ \ 0\ \ (0000000000) .T& cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ \ \ \(em4 to \ \ \ \ 0 \ \ \ \(em2 | \ \ \(em1\ \ (1111111111) .T& cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \(em2048 to \(em2044 \(em2046 | \(em512\ \ (1000000000) _ .T& cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . 1 +1022 to +1024 +1023 | +511\ \ (0111111111) 13 bits .T& cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ \ \ \ 0 to \ \ \ +2 \ \ \ +1 | \ \ \ 0\ \ (0000000000) .T& cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ \ \ \(em2 to \ \ \ \ 0 \ \ \ \(em1 | \ \ \(em1\ \ (1111111111) .T& cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \(em1024 to \(em1022 \(em1023 | \(em512\ \ (1000000000) _ .T& cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . 0 \ +511 to \ +512 +511.5 +511\ \ (0111111111) 14 bits .T& cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ \ \ \ 0 to \ \ \ +1 \ \ +0.5 \ \ \ 0\ \ (0000000000) .T& cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ \ \ \(em1 to \ \ \ \ 0 \ \ \(em0.5 \ \ \(em1\ \ (1111111111) .T& cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ \(em512 to \ \(em511 \(em511.5 \(em512\ \ (1000000000) .TE .LP MSB Most significant bits. .LP LSB Less significant bits. .nr PS 9 .RT .ad r \fBTableau 2/J.41 [T2.41], p.\fR .sp 1P .RT .ad b .RT .LP .sp 13 .bp .LP .rs .sp 47P .ad r \fBFigure 3/J.41 \ \ (\*`a l'italienne), p.\fR .sp 1P .RT .ad b .RT .LP .bp .sp 1P .LP 5.2.4 \fISample error protection\fR .sp 9p .RT .PP 32 bits per frame are used for sample error detection on the basis of\ 1 parity bit per 3\ samples. Odd parity is employed, i.e., the total number of data bits set to state\ 1, in the protected samples, plus the parity bit is always an odd number. The distribution of the parity bits within the frame and the allocation of the parity bits to the samples is shown in Figure\ 3/J.41 and Table\ 3/J.41, respectively. Only the\ 5 most significant bits of the samples are protected. In order to ensure that, if two sequential bits are corrupted, the error can still be detected by the parity checking process, the protected and unprotected bits of each sample are interleaved in descending and ascending order, respectively:\ 1, \fI10\fR , 2, \fI9\fR , 3, \fI8\fR , 4, \fI7\fR , 5, \fI6\fR . LSB is transmitted first and the bits underlined are those protected by the parity check. Error concealment should be used and can be achieved, for example, by replacing an erroneous sample value by a sample value calculated by linear interpolation between adjacent correct samples, or by extrapolation of the previous sample if the following sample is itself in error. .RT .ce \fBH.T. [T3.41]\fR .ce TABLE\ 3/J.41 .ce \fBAllocation of parity bits to the samples\fR .ps 9 .vs 11 .nr VS 11 .nr PS 9 .TS center box; cw(54p) | cw(60p) | cw(54p) | cw(60p) . Parity bit Protects samples Parity bit Protects samples _ .T& cw(54p) | cw(60p) | cw(54p) | cw(60p) . \ 1 \ 3, 35, 66 17 14, 47, 78 .T& cw(54p) | cw(60p) | cw(54p) | cw(60p) . \ 2 \ 8, 39, 71 18 18, 52, 83 .T& cw(54p) | cw(60p) | cw(54p) | cw(60p) . \ 3 12, 44, 75 19 23, 58, 89 .T& cw(54p) | cw(60p) | cw(54p) | cw(60p) . \ 4 17, 48, 79 20 27, 63, 95 .T& cw(54p) | cw(60p) | cw(54p) | cw(60p) . \ 5 21, 53, 84 21 15, 50, 80 .T& cw(54p) | cw(60p) | cw(54p) | cw(60p) . \ 6 26, 57, 88 22 22, 56, 85 .T& cw(54p) | cw(60p) | cw(54p) | cw(60p) . \ 7 31, 62, 92 23 29, 61, 91 .T& cw(54p) | cw(60p) | cw(54p) | cw(60p) . \ 8 19, 51, 82 24 \ 0, 34, 65 .T& cw(54p) | cw(60p) | cw(54p) | cw(60p) . \ 9 24, 55, 86 25 \ 5, 40, 70 .T& cw(54p) | cw(60p) | cw(54p) | cw(60p) . 10 28, 60, 90 26 10, 45, 74 .T& cw(54p) | cw(60p) | cw(54p) | cw(60p) . 11 32, 64, 94 27 \ 7, 33, 68 .T& cw(54p) | cw(60p) | cw(54p) | cw(60p) . 12 \ 2, 37, 69 28 13, 38, 76 .T& cw(54p) | cw(60p) | cw(54p) | cw(60p) . 13 \ 6, 42, 73 29 16, 43, 81 .T& cw(54p) | cw(60p) | cw(54p) | cw(60p) . 14 11, 46, 77 30 20, 49, 87 .T& cw(54p) | cw(60p) | cw(54p) | cw(60p) . 15 \ 4, 36, 67 31 25, 54, 93 .T& cw(54p) | cw(60p) | cw(54p) | cw(60p) . 16 \ 9, 41, 72 32 \ 1, 30, 59 .TE .LP This order has been chosen: .LP a) to spread each group of 3 protected samples as widely as possible; .LP b) to spread the 18 or 21 samples protected by each housekeeping word, with the maximum number of other samples between them. .nr PS 9 .RT .ad r \fBTableau 3/J.41 [T3.41], p.\fR .sp 1P .RT .ad b .RT .sp 1P .LP 5.2.5 \fISingle channel frame format\fR .sp 9p .RT .PP Three 32 sample blocks, together with various housekeeping bits, form a single channel frame having a bit rate of 338\ kbit/s and a duration of 3\ ms. The number of bits per frame is therefore 3338\ =\ 1014\ bits, and these have been allocated as shown in Table\ 4/J.41. Figure\ 3/J.41 illustrates the frame arrangement for a single channel. Two frames are shown in Figure\ 3/J.41 and this format is referred to as a multiframe. Framing information is reversed, i.e.\ alternate bits in each frame of the multiframe. .RT .sp 1P .LP 5.2.6 \fITwo channels (stereo\(hypair) format\fR .sp 9p .RT .PP Two separate 338 kbit/s streams are used to form a stereo\(hypair. Each of these bit streams is arranged as shown in Figure\ 3/J.41. The coders of the stereo\(hypair must be in synchronization. Care must be taken at the receiving end to compensate for any phase difference between the 2\ channels. .RT .sp 1P .LP 5.2.7 \fISynchronization of the 338\(hykbit/s stream\fR .sp 9p .RT .PP The 338 kbit/s stream is synchronized to the coder sampling frequency. .bp .RT .ce \fBH.T. [T4.41]\fR .ce TABLE\ 4/J.41 .ce \fBBit allocation in the frame\fR .ps 9 .vs 11 .nr VS 11 .nr PS 9 .TS center box; lw(84p) | cw(48p) | cw(48p) . Frame allocation (bits/frame) Bit rate per channel (kbit/s) _ .T& lw(84p) | cw(48p) | cw(48p) . Sample words \ 960 320.0 .T& lw(84p) | cw(48p) | cw(48p) . { Range coding \ (including error protection) } \ \ 11 \ \ 3.6 .T& lw(84p) | cw(48p) | cw(48p) . Sample word error protection \ \ 32 \ 10.6 .T& lw(84p) | cw(48p) | cw(48p) . Signalling \ \ \ 4 \ \ 1.3 .T& lw(84p) | cw(48p) | cw(48p) . Frame alignment \ \ \ 7 \ \ 2.3 .T& lw(84p) | cw(48p) | cw(48p) . Total 1014 338.0 _ .TE .nr PS 9 .RT .ad r \fBTableau 4/J.41 [T4.41], p.\fR .sp 1P .RT .ad b .RT .sp 1P .LP 5.2.8 \fILoss and recovery of frame alignment\fR .sp 9p .RT .PP One of the following strategies is used: .RT .LP a) Loss of single channel frame alignment shall occur if two or more consecutive frame alignment words are received incorrectly (for this purpose, bits\ F1 to\ F7, Frame\ 0, and bits F8 to\ F14, Frame\ 1, are both considered as frame alignment words: see Figure\ 3/J.41). An incorrect frame alignment signal is defined as one in which two or more bits are in error. Realignment shall be achieved when a single frame alignment signal is received correctly. If this word is a spurious code, a second attempt at realignment shall be made. .LP b) Only bits\ 1 to\ 10 of the\ 14 bit frame alignment word, derived from Frame\ 0 and Frame\ 1 (see Figure\ 3/J.41), are taken into account at the receiving end. Loss of frame alignment is assumed to have occurred when three consecutive frame alignment signals are received incorrectly in their predicted position. When frame alignment is assumed to have been lost, the automatic frame alignment recovery device will decide that alignment has been recovered when it registers two consecutive correct frame alignment signals. .sp 2P .LP 5.3 \fIConversion from 338 kbit/s to 384 kbit/s\fR .sp 1P .RT .sp 1P .LP 5.3.1 \fIFrame structure\fR .sp 9p .RT .PP The frame structure (see Figure 4/J.41) with a nominal bit rate of 384\ kbit/s and 613\ bits in length is composed of: .RT .LP \(em data input of 338 kbit/s; .LP \(em 63 redundancy bits for single error correction; .LP \(em bits for justification (J) and for identifiction of justification\ (IJ); .LP \(em the frame alignment (FA) signal. .PP The frame is arranged in 4 sections. .sp 1P .LP 5.3.2 \fIJustification strategy\fR .sp 9p .RT .PP The first bits of sections 2, 3 and 4 are used to identify justification. .PP The 462nd bit of the frame (second bit of the fourth section) is the justification bit. .PP In cases of justification, the justification bit may assume any value. .PP Where there is no justification, the position of the justification bit is occupied by an information bit. .PP On the basis of a majority criterion, the demultiplexer recognizes that justification has taken place, if two out of three justification identification bits are in state\ 1. .bp .RT .LP .rs .sp 17P .ad r \fBFigure 4/J.41, p.\fR .sp 1P .RT .ad b .RT .sp 1P .LP 5.3.3 \fIError protection for the 338\(hykbit/s stream\fR .sp 9p .RT .PP A redundancy of 7 bits is calculated every 60\ bits (see Figure\ 4/J.41), to allow for the correction of a single error (Hamming code\ 67, 60) on reception of each group of 67\ bits. The first bit transmitted in a group of 60\ bits is considered as the most significant bit of the group for the computation of the redundancy. The first bit transmitted among the 7\ redundancy bits represents the most significant bit of the remainder. .PP The polynomial generator is equal to x\u7\d\ +\ x\ +\ 1. .RT .sp 1P .LP 5.3.4 \fISynchronization of the 384 kbit/s stream\fR .sp 9p .RT .PP At the output of the coder, the 384 kbit/s stream is synchronously locked to the subsequent primary hierarchical level digital stream. .RT .sp 1P .LP 5.3.5 \fILoss and recovery of frame alignment\fR .sp 9p .RT .PP Loss of frame alignment is assumed to have occurred when three consecutive frame alignment signals are incorrectly received in their predicted position. When frame alignment is assumed to have been lost, the automatic frame alignment recovery device will decide that alignment has been recovered when it registers two consecutive correct frame alignment signals. .RT .sp 1P .LP 5.4 \fIDigital interface at 384 kbit/s\fR .sp 9p .RT .PP Under study. .RT .sp 1P .LP 5.5 \fIFault conditions and consequent action\fR .sp 9p .RT .PP Under study. .RT .sp 2P .LP \fB6\fR \fBDigital interface between equipments using different\fR \fBcoding standards\fR .sp 1P .RT .PP Under study. .RT .sp 2P .LP \fBReferences\fR .sp 1P .RT .LP [1] CCIR Recommendation \fITransmission of analogue high\(hyquality sound\(hyprogramme signals on mixed\fR \fIanalogue and digital circuits using 384\ kbit/s channels\fR , Vol.\ XII, Rec.\ 660, UIT, Geneva,\ 1986. .bp .ce 1000 ANNEX\ A .ce 0 .ce 1000 (to Recommendation J.41) .sp 9p .RT .ce 0 .ce 1000 \fB \fBCoding methods for use by bilateral agreement\fR .sp 1P .RT .ce 0 .ce 1000 (see \(sc 3.3 of this Recommendation) .sp 9p .RT .ce 0 .LP .sp 2 .ce \fBH.T. [T5.41]\fR .ce TABLE\ A\(hy1/J.41 .ps 9 .vs 11 .nr VS 11 .nr PS 9 .TS center box; lw(84p) | cw(48p) | cw(48p) | cw(48p) . Nominal bandwidth 0.04\(hy15 (Note 1) 0.04\(hy15 (Note 1) kHz .T& lw(84p) | cw(48p) | cw(48p) | cw(48p) . Pre/de\(hyemphasis (Note 2) (None) \(em .T& lw(84p) | cw(48p) | cw(48p) | cw(48p) . Overload point (Note 3) +12 +12 dBm0s .T& lw(84p) | cw(48p) | cw(48p) | cw(48p) . Sampling frequency \ 32 \ 32 kHz _ .T& lw(84p) | cw(48p) | cw(48p) | cw(48p) . Companding law 13 segments 7 segments \(em .T& lw(84p) | cw(48p) | cw(48p) | cw(48p) . Bit rate reduction 14/10 13/11 bits _ .T& lw(84p) | cw(48p) | cw(48p) | cw(48p) . { Finest resolution and corresponding noise } \ 14 | \ \(em66 | \ \ 13 \(em55 bits/sample dBq0ps _ .T& lw(84p) | cw(48p) | cw(48p) | cw(48p) . { Coarsest resolution at +9 dBm0s/\fIf\fR 0 | ua\d\u)\d and corresponding noise } \ \ 8 | \ \(em30 | \ \ 10 \(em37 bits/sample dBq0ps _ .T& lw(84p) | cw(48p) | cw(48p) | cw(48p) . { Resolution at +9 dBm0s/60 Hz and corresponding noise } \ 10 | \ \(em42 | \ \ 10 \(em37 bits/sample dBq0ps _ .T& lw(84p) | cw(48p) | cw(48p) | cw(48p) . Source coding \ 320 | \ \ 352 kbit/s .T& lw(84p) | cw(48p) | cw(48p) | cw(48p) . Error protection \ 16 | \ \ 32 kbit/s .T& lw(84p) | cw(48p) | cw(48p) | cw(48p) . Framing and signalling \ \ 0.66 \ \ 0 kbit/s .T& lw(84p) | cw(48p) | cw(48p) | cw(48p) . Service bit rate \ 336.66 \ 384 kbit/s .T& lw(84p) | cw(48p) | cw(48p) | cw(48p) . Transmission bit rate 336.66 | ub\d\u)\d\ 384 \ 384 kbit/s _ .T& lw(84p) | cw(48p) | cw(48p) | cw(48p) . Proposed by Italy Japan .TE .LP \ua\d\u)\d \fIf\fR 0 = zero loss frequency of pre\(hyemphasis. .LP \ub\d\u)\d Dedicated frame. .LP \fINote\ 1\fR \ \(em\ Performance characteristics for analogue 15 kHz type sound\(hyprogramme circuits are given in Recommendation\ J.21 and the proposals are assumed to meet these requirements with at least three codecs in tandem. .LP \fINote\ 2\fR \ \(em\ The pre\(hyemphasis used is: .LP insertion loss = 10 log [ unable to convert formula ] .LP \fINote\ 3\fR \ \(em\ This is defined as the maximum r.m.s. level of sinusoidal signal which does not cause clipping: this value is independent of frequency if analogue peak limiter and pre\(hyemphasis are removed and replaced by zero dB loss; with pre\(hyemphasis the overload level is defined at the zero\ dB loss frequency ( \fIf\fR 0). For detailed information, see Table I in CCIR Report 647. .LP } _ .TE .nr PS 9 .RT .ad r \fBTableau A\(hy1/J.41 [T5.41], p.\fR .sp 1P .RT .ad b .RT .LP .rs .sp 4P .ad r \fBBlanc\fR .ad b .RT .LP .bp .sp 2P .LP \fBRecommendation\ J.42\fR .RT .sp 2P .ce 1000 \fBCHARACTERISTICS\ OF\ \fR \fBEQUIPMENT\ FOR\ THE\ CODING\fR .EF '% Fascicle\ III.6\ \(em\ Rec.\ J.42'' .OF '''Fascicle\ III.6\ \(em\ Rec.\ J.42 %' .ce 0 .ce 1000 \fBOF\ ANALOGUE\ MEDIUM\ QUALITY\ SOUND\(hyPROGRAMME\ SIGNALS\fR .ce 0 .sp 1P .ce 1000 \fBFOR\ TRANSMISSION\ ON\ 384\(hykbit/s\ CHANNELS\fR .ce 0 .sp 1P .ce 1000 \fI(Malaga\(hyTorremolinos, 1984; amended at Melbourne, 1988)\fR .sp 9p .RT .ce 0 .sp 1P .LP \fB1\fR \fBGeneral\fR .sp 1P .RT .PP 1.1 This Recommendation gives the characteristics of equipment for the coding of 7\ kHz monophonic analogue sound\(hyprogramme signals into a digital signal. Two monophonic digital signals can be combined to form a\ 384\(hykbit/s signal already specified in Recommendation\ J.41. .sp 9p .RT .PP 1.2 Equipment for coding of analogue sound\(hyprogramme signals, as specified in this Recommendation, can be: .sp 9p .RT .LP a) A stand alone encoder/decoder with a digital interface at 384\ kbit/s. The encoder operation and the decoder operation may be performed in two separate equipments or in the same equipment. .LP b) A combined encoder\(hymultiplex decoder\(hydemultiplex with a digital interface at\ 1544 or 2048\ kbit/s. The encoder\(hymultiplex operation and the decoder\(hymultiplex operation may be performed in two separate equipments or in the same equipment. .PP In case b) it is not mandatory to provide an external digital sound\(hyprogramme access port at 384\ kbit/s. .sp 2P .LP \fB2\fR \fBTransmission performance\fR .sp 1P .RT .PP The transmission performance per encoder/decoder pair shall be such that the limits specified in Recommendation\ J.23 (CCIR Recommendation\ 503) are not exceeded by three encoder/decoder pairs connected in tandem at audio frequencies. .RT .sp 2P .LP \fB3\fR \fBMethod of encoding\fR .sp 1P .RT .PP 3.1 The recommended encoding laws are as specified in [1]. .sp 9p .RT .PP 3.2 These encoding laws are based on a uniformly quantized, 14\(hybit per sample PCM technique with companding and employ either: .sp 9p .RT .LP a) eleven\(hysegment 14 to 11 bit instantaneous A\(hylaw companding, or .LP b) five\(hyrange 14 to 10 bit near\(hyinstantaneous companding. .PP 3.3 Equipment characteristics common to both methods of encoding are: .sp 9p .RT .LP Nominal audio bandwidth: 0.05 to 7 kHz. Audio interface: see Recommendation J.23, \(sc\ 2. Sampling frequency: 16 (1\ \(+-\ 5\ \(mu\ 10\uD\dlF261\u5\d) kHz. Pre/de\(hyemphasis: Recommendation J.17 with 6.5\ dB attenuation at 800\ Hz. .LP .bp .PP \fINote\fR \ \(em\ Pre\(hyemphasis and de\(hyemphasis are not used by the Administrations of Canada, Japan and the United States of America on their national circuits and on international circuits between each other, but are used on international circuits to other countries. .sp 2P .LP \fB4\fR \fBEquipment using \fR \fBinstantaneous companding\fR .sp 1P .RT .sp 1P .LP 4.1 \fICoding table\fR \v'3p' .sp 9p .RT .PP 4.1.1 The coding law is specified in Table\ 1/J.41. .PP 4.1.2 The allocation of character signals (PCM code words) is also given in Table\ 1/J.41. Two variants (A\ and\ B) of character signals are allowed. .PP \fINote\fR \ \(em\ In the case of digital interconnection between variants\ A and\ B, the conversion from one set of character signals to the other set in Table\ 1/J.41, can be done without any performance degradation. In the case of analogue interconnection, a reduction in the S/N\ ratio, in the order of 3\ dB, is expected. .sp 1P .LP 4.2 \fIBit rates\fR \v'3p' .sp 9p .RT .LP Nominal source coding bit rate (16 kHz\ \(mu\ 11 bit/sample) 176 kbit/s Error protection (16 kHz\ \(mu\ 1 bit/sample) 16 kbit/s Transmission bit rate per sound\(hyprogramme signal 192 kbit/s Channel bit rate for 2 sound\(hyprogramme signals 384 kbit/s .sp 1P .LP 4.3 \fIOverload level\fR .sp 9p .RT .PP The overload level for a sine\(hywave signal at zero\ dB insertion loss frequency (2.1\ kHz) of the pre\(hyemphasis is +15\ dBm0s. .RT .sp 1P .LP 4.4 \fIDigital signal format\fR .sp 9p .RT .PP The character signal bit sequences for variants A and B, are shown in Figure\ 1/J.41. .RT .sp 1P .LP 4.4.1 \fIVariant A\fR .sp 9p .RT .PP When transmitting two monophonic digital signals as one 384 kbit/s signal, with respect to the code word interleaving shown in Figure\ 1/J.41, the first two 12\ bit code words are allocated to 7\ kHz channel\ No.\ 1 and the second two 12\ bit code words are allocated to 7\ kHz channel\ No.\ 2. .RT .sp 1P .LP 4.4.2 \fIVariant B\fR .sp 9p .RT .PP The 12 bit code word assignments when transmitting two monophonic digital signals as one\ 384\(hykbit/s signal is under study. .RT .sp 1P .LP 4.5 \fIBit error protection\fR .sp 9p .RT .PP One parity bit is added to each 11\(hybit character signal. .RT .sp 1P .LP 4.5.1 \fIVariant A\fR .sp 9p .RT .PP The five most important bits of each sample are protected against errors by means of a parity bit. In the converter of the transmitting part, the parity bit is added as the\ 12th bit to each code word. Its value is fixed so that the 6\ bit parity block always contains only an odd number of one values. In order that even bit error structures can also result in parity violations, the protected and unprotected bits of each code word are interleaved in ascending and descending sequence, as shown in Figure\ 1/J.41. .RT .sp 1P .LP 4.5.2 \fIVariant B\fR .sp 9p .RT .PP The added parity bit shall be based on the 7 most significant bits of the 11\(hybit PCM word. These are bits S, X, Y, Z, A, B,\ C. The parity of \*Qones\*U bit shall be \fIeven\fR . Since the chord bits (X, Y, Z) always contain a one, the minimum number of ones per sample is\ 2, resulting in a minimum ones density of\ 1/6. .bp .RT .sp 1P .LP 4.5.3 \fIError concealment\fR .sp 9p .RT .PP If a parity violation is detected, an error concealment technique should be applied (for instance, replacement by interpolation, extrapolation or repetition). For multiple parity violation (error bursts), a muting technique should be applied. .RT .sp 1P .LP 4.6 \fIDigital interface at 384 kbit/s\fR .sp 9p .RT .PP Under study (see Recommendations\ G.735 and G.737). .RT .sp 1P .LP 4.7 \fISynchronization\fR .sp 9p .RT .PP The coding equipment operates in synchronism with the clock of subsequent multiplex equipment or the network clock. In cases where the digital interface is provided, bit and byte (24 bit, as shown in Figure\ 1/J.41) timing information is required. .PP Variant A: A solution for synchronous access is given in the Recommandations\ G.735 and\ G.737. .PP Variant B: The solution for synchronous access is under study. .RT .sp 2P .LP 4.8 \fIFault condition and consequent actions\fR .sp 1P .RT .sp 1P .LP 4.8.1 \fIVariant A\fR .sp 9p .RT .PP Where a 384\(hykbit/s digital interface is provided, the same principles for fault conditions and subsequent actions as those outlined in Recommendation\ G.732, should be followed. .RT .sp 1P .LP 4.8.2 \fIVariant B\fR .sp 9p .RT .PP Under study. .RT .sp 2P .LP \fB5\fR \fBEquipment using \fR \fBnear\(hyinstantaneous companding\fR .sp 1P .RT .sp 1P .LP 5.1 \fIIntroduction\fR .sp 9p .RT .PP The equipment described in this section uses the near\(hyinstantaneous method of companding in the coding of medium quality sound\(hyprogramme signals into digital form. .PP A two\(hystage process is used in the encoding equipment: .RT .LP a) Conversion of a 7 kHz channel into a 169 kbit/s stream. .LP \fINote\fR \ \(em\ The value of 169 kbit/s has been chosen to allow for the possible multiplexing of 12\ channels into a 2048\ kbit/s dedicated frame format. .LP b) Asynchronous insertion of two synchronous 169 kbit/s streams into a 384\ kbit/s stream. .LP \fINote\fR \ \(em\ The asynchronous insertion of two synchronous 169\ kbit/s streams into a 384\ kbit/s stream allows the use, at the encoder location, of a clock not necessarily synchronous to the network clock. It can be advantageous when the encoder equipment and the insertion equipment (see Recommendations\ G.735 and\ G.737) are located in different places, and when the transmission link between them is unidirectional, .LP and the reverse processes in the decoding equipment. .sp 2P .LP 5.2 \fIConversion from 7 kHz to 169 kbit/s and constitution of the\fR \fI338\(hykbit/s signal\fR .sp 1P .RT .sp 1P .LP 5.2.1 \fIOverload level\fR .sp 9p .RT .PP The overload level for a sine\(hywave signal at the zero\ dB insertion loss frequency (2.1\ kHz) of the pre\(hyemphasis circuit is\ +12\ dBm0s. .bp .RT .sp 1P .LP 5.2.2 \fICompanding\fR .sp 9p .RT .PP The same near\(hyinstantaneous companding procedure with a block of 32\ samples (2\ ms) as described in \(sc\ 5.2.2 of Recommendation\ J.41, is used. The character signal is coded in\ 2's complement form. .RT .sp 1P .LP 5.2.3 \fIConstitution of the 338\(hykbit/s signal\fR .sp 9p .RT .PP Two 7\(hykHz channels (C1 and C2) are contained in one 338\(hykbit/s stream. The frame structure of the 338\ kbit/s stream is defined in \(sc\ 5.2.5 and in Figure\ 3/J.41. The following numbering of the samples within a given multiframe is defined as follows (see Figure\ 3/J.41): .PP Sample \fIn\fR of the multiframe is sample (\fIn\fR \ \(em\ 96\fIi\fR ) of frame\ \fIi\fR .RT .sp 1P .ce 1000 0\ \(=\ \fIn\fR \ \(=\ 191\ \ \ \ \fIi\fR \ =\ 0 or 1 .ce 0 .sp 1P .PP Using the above notation, the following relationship between the bits of the\ 338 kbit/s multiframe and channels\ C1 and\ C2 can be defined: .PP Sample 2\fIn\fR of the multiframe corresponds to sample \fIn\fR of channel\ C1 .PP Sample (2\fIn\fR \ +\ 1) of the multiframe corresponds to sample \fIn\fR of channel\ C2 .RT .sp 1P .ce 1000 0\ \(=\ \fIn\fR \ \(=\ 95 .ce 0 .sp 1P .PP Range coding information associated with block (2\fIn\fR \ \(em\ 1) of the multiframe is allocated to block\ \fIn\fR of channel\ C1 (derived from C1\ samples in blocks (2\fIn\fR \ \(em\ 1) and (2\fIn\fR ) of the multiframe). .PP Range coding information associated with block (2\fIn\fR ) of the multiframe is allocated to block\ \fIn\fR of channel\ C2 (derived from C2\ samples in blocks (2\fIn\fR \ \(em\ 1) and (2\fIn\fR ) of the multiframe). .RT .sp 1P .ce 1000 1\ \(=\ \fIn\fR \ \(=\ 3 .ce 0 .sp 1P .PP The range coding information and its protection, the sample format and the sample error protection are defined and transmitted as specified in this Recommendation and in \(sc\(sc\ 5.2.3 to\ 5.2.5 of Recommendation\ J.41. .PP The criteria for loss and recovery of frame alignment at 338 kbit/s is defined in \(sc\ 5.2.8 of Recommendation\ J.41. .RT .sp 1P .LP 5.3 \fIConversion from 338 kbit/s to 383 kbit/s\fR .sp 9p .RT .PP See Recommendation J.41, \(sc\ 5.3. .RT .sp 1P .LP 5.4 \fIDigital interface at 384 kbit/s\fR .sp 9p .RT .PP Under study. .RT .sp 1P .LP 5.5 \fIFault conditions and consequent action\fR .sp 9p .RT .PP Under study. .RT .sp 2P .LP \fB6\fR \fBDigital interface between equipments using different\fR \fBcoding standards\fR .sp 1P .RT .PP Under study. \v'1P' .RT .sp 2P .LP \fBReferences\fR .sp 1P .RT .LP [1] CCIR Recommandation \fITransmission of analogue high\(hyquality sound\(hyprogramme signals on mixed\fR \fIanalogue and digital circuits using 384\ kbit/s channels\fR , Vol.\ XII, Rec.\ 660, ITU, Geneva,\ 1986. .LP .rs .sp 6P .ad r \fBBlanc\fR .ad b .RT .LP .bp .sp 2P .LP \fBRecommendation\ J.43\fR .RT .sp 2P .ce 1000 \fBCHARACTERISTICS\ OF\ EQUIPMENT\ FOR\ THE\ CODING\ OF\ \fR \fBANALOGUE\fR .EF '% Fascicle\ III.6\ \(em\ Rec.\ J.43'' .OF '''Fascicle\ III.6\ \(em\ Rec.\ J.43 %' .ce 0 .sp 1P .ce 1000 \fBHIGH\ QUALITY\ SOUND\ PROGRAMME\ SIGNALS\ FOR\ TRANSMISSION\ ON | 320\ kbit/s\ CHANNELS\fR .FS Digital interfaces between Administrations which have adopted different systems should, if a bilateral agreement is not reached, operate at 384\ kbit/s (H\d0\u\ channel) and carry signals encoded, according to Recommendation\ J.41, \(sc\ 4. Any necessary transcoding will be carried out by Administrations using the system specified in this Recommendation. .FE .ce 0 .sp 1P .ce 1000 \fI(Melbourne, 1988)\fR .sp 9p .RT .ce 0 .sp 1P .LP \fB1\fR \fBGeneral\fR .sp 1P .RT .PP 1.1 This Recommendation gives the characteristics of equipment for the coding of 15\ kHz monophonic analogue sound\(hyprogramme signals into a digital signal of 320\ kbit/s. For stereophonic operation, two monophonic digital codecs can be utilized. Two monophonic digital signals that form a stereophonic signal should be routed together over the same transmission systems (path) to avoid difference in transmission delay. .sp 9p .RT .PP 1.2 Equipment for coding of analogue sound\(hyprogramme signals can be: .LP a) A stand\(hyalone encoder/decoder with a digital interface at 320\ kbit/s. The encoder operation and the decoder operation may be performed in two separate equipments or in the same equipment. .LP b) A combined encoder\(hymultiplex/decoder\(hydemultiplex with a digital interface at\ 1544 or 2048\ kbit/s. The encoder\(hymultiplex operation and the decoder\(hydemultiplex operation may be performed in two separate equipments or in the same equipment. .PP In case b), it is not mandatory to provide an external access at 320\ kbit/s. .sp 2P .LP \fB2\fR \fBTransmission performance\fR .sp 1P .RT .PP The transmission performance per encoder/decoder pair shall be such that the limits specified in Recommendation\ J.21 (CCIR Recommendation\ 505) are not exceeded by three encoder/decoder pairs connected in tandem at audio frequencies. .RT .sp 2P .LP \fB3\fR \fBMethod of encoding\fR .sp 1P .RT .PP 3.1 The encoding method is based on a uniformly quantized 14\(hybit per sample\ PCM technique with differential\ 14\(hy to\ 9.5\(hybit near instantaneous companding. .sp 9p .RT .PP 3.2 Fundamental characteristics of the equipment are: .LP Nominal\ audio\ bandwidth: 0.04 to 15 kHz. .LP Audio\ interface: see Recommendation J.21, \(sc 2. .LP Sampling\ frequency .LP (CCIR\ Recommendation\ 606): 32 (1 + 5 \(mu 10\uD\dlF261\u5\d) kHz, .LP Pre/de\(hyemphasis: Recommendation J.17 with 6.5 dB attenuation at 800\ Hz. .sp 2P .LP \fB4\fR \fBCharacteristics of the equipment\fR .sp 1P .RT .sp 1P .LP 4.1 \fIIntroduction\fR .sp 9p .RT .PP The equipment being described uses the differential near\(hyinstantaneous method of companding in the coding of high\(hyquality sound\(hyprogramme signals into digital form. .PP A two\(hystage process is used in the encoding equipment: .RT .LP a) conversion of a 15 kHz channel into a 316 kbit/s stream; .LP b) asynchronous insertion of the 316 kbit/s stream into a 320 kbit/s stream; .bp .PP \fINote\fR \ \(em\ The asynchronous insertion of the 316 kbit/s stream into a 320\ kbit/s stream allows the use, at the encoder location, of a clock not necessarily synchronous to the network clock. It can be advantageous when the encoder equipment and the insertion equipment are located in different places, and when the transmission link between them is unidirectional, .PP and the reverse processes in the decoding equipment. .RT .sp 2P .LP 4.2 \fIConversion from 15 kHz to 316 kbit/s\fR .sp 1P .RT .sp 1P .LP 4.2.1 \fIOverload level\fR .sp 9p .RT .PP The overload level for a sine\(hywave signal at the zero dB insertion loss frequency (2.1\ kHz) of the pre\(hyemphasis circuit is +12 or +15\ dBm0s. .RT .sp 1P .LP 4.2.2 \fICompanding\fR .sp 9p .RT .PP Differential near\(hyinstantaneous companding is used to achieve a data rate reduction from 14\ bits/sample to 9.5\ bit/sample. The process of differential near\(hyinstantaneous companding is subdivided into the following stages: .RT .LP a) near\(hyinstantaneous companding to achieve a data rate reduction from 14\ bits/sample to 10\ bits/sample as in \(sc\ 5 of Recommendation\ J.41. The system coded a bloc of 32\ samples into one of 5\ gain ranges, according to the highest value sample in the block. The companding characteristic is shown diagramatically in Figure\ 1/J.43 and the parameters are specified in Table\ 1/J.43; .LP .rs .sp 31P .ad r \fBFigure 1/J.43, p.10\fR .sp 1P .RT .ad b .RT .LP .bp .ce \fBH.T. [T1.43]\fR .ce TABLE\ 1/J.43 .ce \fB14 to 10 bit near\(hyinstantaneous\fR .ce \fBcompanding law\fR .ps 9 .vs 11 .nr VS 11 .nr PS 9 .TS center box; cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . Range Normalized analogue input Normalized analogue output { Compressed digital code MSB LSB } Effective resolution _ .T& cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . 4 +8176 to +8192 +8184 | +511\ \ (0111111111) 10 bits .T& cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ \ \ \ 0 to \ \ +16 \ \ \ +8 | \ \ \ 0\ \ (0000000000) .T& cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ \ \(em16 to \ \ \ \ 0 \ \ \ \(em8 | \ \ \(em1\ \ (1000000000) .T& cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \(em8192 to \(em8176 \(em8184 | \(em512\ \ (1111111111) _ .T& cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . 3 +4088 to +4096 +4092 | +511\ \ (0111111111) 11 bits .T& cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ \ \ \ 0 to \ \ \ +8 \ \ \ +4 | \ \ \ 0\ \ (0000000000) .T& cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ \ \ \(em8 to \ \ \ \ 0 \ \ \ \(em4 | \ \ \(em1\ \ (1000000000) .T& cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \(em4096 to \(em4088 \(em4092 | \(em512\ \ (1111111111) _ .T& cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . 2 +2044 to +2048 +2046 | +511\ \ (0111111111) 12 bits .T& cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ \ \ \ 0 to \ \ \ +4 \ \ \ +2 | \ \ \ 0\ \ (0000000000) .T& cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ \ \ \(em4 to \ \ \ \ 0 \ \ \ \(em2 | \ \ \(em1\ \ (1000000000) .T& cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \(em2048 to \(em2044 \(em2046 | \(em512\ \ (1111111111) _ .T& cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . 1 +1022 to +1024 +1023 | +511\ \ (0111111111) 13 bits .T& cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ \ \ \ 0 to \ \ \ +2 \ \ \ +1 | \ \ \ 0\ \ (0000000000) .T& cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ \ \ \(em2 to \ \ \ \ 0 \ \ \ \(em1 | \ \ \(em1\ \ (1000000000) .T& cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \(em1024 to \(em1022 \(em1023 | \(em512\ \ (1111111111) _ .T& cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . 0 \ +511 to \ +512 +511.5 +511\ \ (0111111111) 14 bits .T& cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ \ \ \ 0 to \ \ \ +1 \ \ +0.5 \ \ \ 0\ \ (0000000000) .T& cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ \ \ \(em1 to \ \ \ \ 0 \ \ \(em0.5 \ \ \(em1\ \ (1000000000) .T& cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ \(em512 to \ \(em511 \(em511.5 \(em512\ \ (1111111111) .TE .IP MSB Most significant bit. .IP LSB Least significant bit. .nr PS 9 .RT .ad r \fBTableau 1/J.43 [T1.43], p.11\fR .sp 1P .RT .ad b .RT .LP .sp 13 .bp .LP b) division of a sequence of samples \fIx\fR (\fIn\fR ) into two sequences one of which is a sequence of odd samples\ \fIx\fR (2\ \(em\ 1) and the other is a sequence of even samples\ \fIx\fR (2\fIn\fR ). Calculation of differential even samples\ ?63(2\fIn\fR ) by the formula \v'6p' .ad r .ad b .RT .LP c) additional near\(hyinstantaneous companding of the differential samples\ ?63(2\fIn\fR ) to achieve a data rate reduction from 14\ bits/sample to 9\ bits/sample. The system codes a block of 16\ even samples into one of\ 3 additional gain ranges, according to the highest value sample in the block. The companding characteristic is shown diagrammatically in Figure\ 2/J.43 and the parameters are specified in Table\ 2/J.43. .PP After multiplexing the odd samples \fIx\fR (2\fIn\fR \ \(em\ 1) represented by a compressed code of 10\ bits per sample and the differential even samples\ ?63(2\fIn\fR ) additionally represented by a compressed code of 9\ bits per sample, an average of 9.5\ bits per sample is obtained. .LP .rs .sp 30P .ad r \fBFigure 2/J.43, p.12\fR .sp 1P .RT .ad b .RT .LP .bp .ce \fBH.T. [1T2.43]\fR .ce TABLE\ 2/J.43 .ce \fB14 to 9.0 bit near\(hyinstantaneous\fR .ce \fBcompanding law\fR .ps 9 .vs 11 .nr VS 11 .nr PS 9 .TS center box; cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . Range Normalized input Normalized output { Compressed digital code MSB LSB } Effective resolution _ .T& lw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . 2 +16 | 20 to +16 | 84 +16 | 52 | +255\ \ (011111111) \ 8 bits .T& lw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ \ \ | \ 0 to \ \ \ | 64 \ \ \ | 32 | \ \ \ 0\ \ (000000000) .T& lw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . { \ \ \ | (em64 to \ \ \ | \ 0 } \ \ \ | (em32 | \ \ \(em1\ \ (100000000) .T& lw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \(em16 | 84 to \(em16 | 20 \(em16 | 52 | \(em256\ \ (111111111) .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . 4 1 \ | 8160 to \ | 8192 \ | 8176 | +255\ \ (011111111) \ 9 bits .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ \ \ | \ 0 to \ \ \ | 32 \ \ \ | 16 | \ \ \ 0\ \ (000000000) .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . { \ \ \ | (em32 to \ \ \ | \ 0 } \ \ \ | (em16 | \ \ \(em1\ \ (100000000) .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ | (em8190 to \ | (em8160 \ | (em8176 | \(em256\ \ (111111111) .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . 0 \ | 4080 to \ | 4096 \ | 4088 | +255\ \ (011111111) 10 bits .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ \ \ | \ 0 to \ \ \ | 16 \ \ \ | +8 | \ \ \ 0\ \ (000000000) .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . { \ \ \ | (em16 to \ \ \ | \ 0 } \ \ \ | \(em8 | \ \ \(em1\ \ (100000000) .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ | (em4096 to \ | (em4080 \ | (em4088 | \(em256\ \ (111111111) _ .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . 2 \ | 8160 to \ | 8192 \ | 8176 | +255\ \ (011111111) \ 9 bits .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ \ \ | \ 0 to \ \ \ | 32 \ \ \ | 16 | \ \ \ 0\ \ (000000000) .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . { \ \ \ | (em32 to \ \ \ | \ 0 } \ \ \ | (em16 | \ \ \(em1\ \ (100000000) .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ | (em8192 to \ | (em8160 \ | (em8176 | \(em256\ \ (111111111) .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . 3 1 \ | 4080 to \ | 4096 \ | 4088 | +255\ \ (011111111) 10 bits .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ \ \ | \ 0 to \ \ \ | 16 \ \ \ | +8 | \ \ \ 0\ \ (000000000) .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . { \ \ \ | (em16 to \ \ \ | \ 0 } \ \ \ | \(em8 | \ \ \(em1\ \ (100000000) .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ | (em4096 to \ | (em4080 \ | (em4088 | \(em256\ \ (111111111) .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . 0 \ | 2040 to \ | 2048 \ | 2044 | +255\ \ (011111111) 11 bits .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ \ \ | \ 0 to \ \ \ | +8 \ \ \ | +4 | \ \ \ 0\ \ (000000000) .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . { \ \ \ | \(em8 to \ \ \ | \ 0 } \ \ \ | \(em4 | \ \ \(em1\ \ (100000000) .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ | (em2048 to \ | (em2040 \ | (em2044 | \(em256\ \ (111111111) _ .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . 2 \ | 4080 to \ | 4096 \ | 4088 | +255\ \ (011111111) 10 bits .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ \ \ | \ 0 to \ \ \ | 16 \ \ \ | +8 | \ \ \ 0\ \ (000000000) .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . { \ \ \ | (em16 to \ \ \ | \ 0 } \ \ \ | \(em8 | \ \ \(em1\ \ (100000000) .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ | (em4096 to \ | (em4080 \ | (em4088 | \(em256\ \ (111111111) .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . 2 1 \ | 2040 to \ | 2048 \ | 2044 | +255\ \ (011111111) 11 bits .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ \ \ | \ 0 to \ \ \ | +8 \ \ \ | +4 | \ \ \ 0\ \ (000000000) .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . { \ \ \ | \(em8 to \ \ \ | \ 0 } \ \ \ | \(em4 | \ \ \(em1\ \ (100000000) .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ | (em2048 to \ | (em2040 \ | (em2044 | \(em256\ \ (111111111) .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . 0 \ | 1020 to \ | 1024 \ | 1022 | +255\ \ (011111111) 12 bits .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ \ \ | \ 0 to \ \ \ | +4 \ \ \ | +2 | \ \ \ 0\ \ (000000000) .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . { \ \ \ | \(em4 to \ \ \ | \ 0 } \ \ \ | \(em2 | \ \ \(em1\ \ (100000000) .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ | (em1024 to \ | (em1020 \ | (em1022 | \(em256\ \ (111111111) _ .TE .nr PS 9 .RT .ad r \fBTableau 2/J.43 [1T2.43], p.13\fR .sp 1P .RT .ad b .RT .LP .bp .ce \fBH.T. [2T2.43]\fR .ce TABLE\ 2/J.43 \fI(continuation)\fR .ps 9 .vs 11 .nr VS 11 .nr PS 9 .TS center box; cw(36p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . Range Normalized input Normalized output { Compressed digital code MSB LSB } Effective resolution _ .T& lw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . 2 \ | 2040 to \ | 2048 \ | 2044 | +255\ \ (011111111) 11 bits .T& lw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ \ \ | \ 0 to \ \ \ | +8 \ \ \ | +4 | \ \ \ 0\ \ (000000000) .T& lw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . { \ \ \ | \(em8 to \ \ \ | \ 0 } \ \ \ | \(em4 | \ \ \(em1\ \ (100000000) .T& lw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ | (em2048 to \ | (em2040 \ | (em2044 | \(em256\ \ (111111111) .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . 1 1 \ | 1020 to \ | 1024 \ | 1022 | +255\ \ (011111111) 12 bits .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ \ \ | \ 0 to \ \ \ | +4 \ \ \ | +2 | \ \ \ 0\ \ (000000000) .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . { \ \ \ | \(em4 to \ \ \ | \ 0 } \ \ \ | \(em2 | \ \ \(em1\ \ (100000000) .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ | (em1024 to \ | (em1020 \ | (em1022 | \(em256\ \ (111111111) .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . 0 \ | +510 to \ | +512 \ | +511 | +255\ \ (011111111) 13 bits .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ \ \ | \ 0 to \ \ \ | +2 \ \ \ | +1 | \ \ \ 0\ \ (000000000) .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . { \ \ \ | \(em2 to \ \ \ | \ 0 } \ \ \ | \(em1 | \ \ \(em1\ \ (100000000) .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . { \ | \(em512 to \ | \(em510 } \ | \(em511 | \(em256\ \ (111111111) _ .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . 2 \ | 1020 to \ | 1024 \ | 1022 | +255\ \ (011111111) 12 bits .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ \ \ | \ 0 to \ \ \ | +4 \ \ \ | +2 | \ \ \ 0\ \ (000000000) .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . { \ \ \ | \(em4 to \ \ \ | \ 0 } \ \ \ | \(em2 | \ \ \(em1\ \ (100000000) .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ | (em1024 to \ | (em1020 \ | (em1022 | \(em256\ \ (111111111) .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . 0 1 \ | +510 to \ | +512 \ | +511 | +255\ \ (011111111) 13 bits .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ \ \ | \ 0 to \ \ \ | +2 \ \ \ | +1 | \ \ \ 0\ \ (000000000) .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . { \ \ \ | \(em2 to \ \ \ | \ 0 } \ \ \ | \(em1 | \ \ \(em1\ \ (100000000) .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . { \ | \(em512 to \ | \(em510 } \ | \(em511 | \(em256\ \ (111111111) .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . 0 \ | +255 to \ | +256 \ | +255.5 +255\ \ (011111111) 14 bits .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . \ \ \ | \ 0 to \ \ \ | +1 \ \ \ | +0.5 \ \ \ 0\ \ (000000000) .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . { \ \ \ | \(em1 to \ \ \ | \ 0 } \ \ \ | \(em0.5 \ \ \(em1\ \ (100000000) .T& cw(18p) | cw(18p) | cw(60p) | cw(36p) | cw(60p) | cw(36p) . { \ | \(em256 to \ | \(em255 } \ | \(em255.5 \(em256\ \ (111111111) .TE .LP MSB Most significant bit. .LP LSB Least significant bit. .nr PS 9 .RT .ad r \fBTableau 2/J.43 [2T2.43], p.13\fR .sp 1P .RT .ad b .RT .LP .sp 12 .bp .sp 1P .LP 4.2.3 \fIRange coding\fR .sp 9p .RT .PP The five possible values of a gain range for a block of 32 samples and three possible values of an additional gain range for differential even samples of this block produce 15\ possible values of a complex gain range which is represented by a four\(hybit code word. Complex range codes are shown in Table\ 3/J.43. .RT .LP .sp 1 .ce \fBH.T. [T3.43]\fR .ce TABLE\ 3/J.43 .ps 9 .vs 11 .nr VS 11 .nr PS 9 .TS center box; lw(60p) | cw(24p) | cw(24p) | cw(24p) | cw(24p) | cw(24p) . Basic Additional 0 1 2 3 4 _ .T& cw(60p) | cw(24p) | cw(24p) | cw(24p) | cw(24p) | cw(24p) . 0 1110 1101 1100 1011 1010 .T& cw(60p) | cw(24p) | cw(24p) | cw(24p) | cw(24p) | cw(24p) . 1 1001 1000 0111 0110 0101 .T& cw(60p) | cw(24p) | cw(24p) | cw(24p) | cw(24p) | cw(24p) . 2 0100 0011 0010 0001 0000 _ .TE .nr PS 9 .RT .ad r \fBTableau 3/J.43 [T3.43], p.\fR .sp 1P .RT .ad b .RT .LP .sp 1 .PP For error\(hyprotected transmission, two code words of the complex gain range (which correspond to two blocks) are combined into one\ 8\(hybit code word which is coded by a Hamming code (12,8). This code makes it possible to correct all singla errors in the code word of the complex gain range. .PP A code word of 12 bits comprising 8 bits of the gain range of two blocks and 4\ check bits is transmitted in a cycle having a duration of 2\ ms (ee Figure\ 3/J.43). The first 8\ bits\ R1 to\ R8 correspond to two complex code words. The last four bits (R9\ to\ R12) are check bits. They are determined as follows: \v'6p' .RT .ad r .ad b .RT .PP Modulo 2 addition is designated by \o'\(ci+' and inversion of bit R is designated by\ \fIR\fR . .LP .rs .sp 16P .ad r \fBFigure 3/J.43, p.\fR .sp 1P .RT .ad b .RT .LP .bp .sp 1P .LP 4.2.4 \fISample error protection\fR .sp 9p .RT .PP The 5 most significant bits of 10\(hybit samples and 4 most significant bits of 9\(hydigit samples are protected. One parity bit is generated for 5\ most significant bits of each 10\(hydigit sample. A parity bit is also generated for 4\ most significant bits of each pair of 9\(hydigit samples. A total of 24\ bits are thus generated for a block of 32\ samples. These 24\ parity bits undergo error protection by means of a cyclic code (29,24). The code (29,24) is a shortened Hamming code (31,26). The polynomial generator of the code (29,24) is: \v'6p' .RT .ce 1000 \fIF\fR (\fIx\fR ) = \fIx\fR \u5\d + \fIx\fR \u2\d + 1 .ce 0 .ad r (3) .ad b .RT .LP .sp 1 .PP To the receiving end only the check bits of the cyclic code (29,24) are sent, since 24\ parity bits are reproduced according to the received sample. Thus, 5\ protection bits correspond to a block of 32\ samples, 10\ protection bits for two blocks are transmitted in a cycle having a duration of 2\ ms (see Figure\ 3/J.43). .PP In order to correct 8\(hybit error bursts, samples from four blocks are interleaved. Interleaving of samples from four blocks is shown in Table\ 6/J.43. .PP \fINote\fR \ \(em\ Interleaving of samples from four adjacent blocks is an effective measure of error protection. Samples of a sound\(hyprogramme signal are transmitted over the primary digital path in octets (8\(hybit words). Such samples interleaving ensures correction of erroneous octets. .RT .sp 1P .LP 4.2.5 \fI316 kbit/s channel frame\fR .sp 9p .RT .PP The frame has a duration of 2 ms which corresponds to two 32\(hysample blocks. The frame duration of 2\ ms equals to the multiframe duration of the primary digital multiplex equipment. Due to this coincidence of durations a possibility is provided to use the multiframe alignment signal of the primary digital multiplex equipment. With a digital rate of 316\ kbit/s and a duration of 2\ ms, the frame comprises 632\ bits divided into 8\ groups of 79\ bits each. Bit allocation in the frame is shown in Table\ 4/J.43. .RT .LP .sp 1 .ce \fBH.T. [T4.43]\fR .ce TABLE\ 4/J.43 .ce \fBBit allocation in the frame\fR .ps 9 .vs 11 .nr VS 11 .nr PS 9 .TS center box; lw(108p) | cw(48p) | cw(48p) . Frame allocation (bits/frame) Bit rate per channel (kbit/s) _ .T& lw(108p) | cw(48p) | cw(48p) . Samples 608 304 .T& lw(108p) | cw(48p) | cw(48p) . Range code \ \ 8 \ \ 4 .T& lw(108p) | cw(48p) | cw(48p) . Check bits of a range code \ \ 4 \ \ 2 .T& lw(108p) | cw(48p) | cw(48p) . Check bits of samples \ 10 \ \ 5 .T& lw(108p) | cw(48p) | cw(48p) . Signalling and data bits \ \ 2 \ \ 1 .T& lw(108p) | cw(48p) | cw(48p) . Total 632 316 _ .TE .nr PS 9 .RT .ad r \fBTableau 4/J.43 [T4.43], p.\fR .sp 1P .RT .ad b .RT .LP .sp 1 .PP The frame structure is shown in Figure 3/J.43 and Table 5/J.43. Table\ 6/J.43 shows the allocation of sample bits in a group, which provides for interleaving of samples from four blocks (see \(sc\ 4.2.4 above) and interleaving of bits from different samples. .PP \fINote\fR \ \(em\ As can ben seen from Table 6/J.43, an 8\(hybit error burst disintegrates into isolated single errors. For example, when errors occur in bits\ 1 to\ 8 of the first group (1\ =\ 1) of the N\(hyth frame, errors appear in the next four samples: the first sample of the first block frame\ N\ \(em\ 1 (n\ =\ 1, k\ =\ 1), the second sample of the second block of frame\ N\ \(em\ 1 (n\ =\ 2, k\ =\ 2), the second sample of the first block of frame\ N\ \(em\ 2 (n\ =\ 2, k\ =\ 1), the first sample of the second block of frame\ N\ \(em\ 2 (n\ =\ 1, k\ =\ 2). These isolated errors are corrected by means of interpolation. .bp .RT .ce \fBH.T. [T5.43]\fR .ce TABLE\ 5/J.43 .ce \fB316 kbit/s frame structure\fR .ps 9 .vs 11 .nr VS 11 .nr PS 9 .TS center box; cw(108p) | cw(48p) | cw(48p) . Data type Bit number in a group Group number in a cycle _ .T& lw(108p) | cw(48p) | cw(48p) . Sample bits 1\(hy38; 41 to 78 1 to 8 .T& lw(108p) | cw(48p) | cw(48p) . { Bits of the code words of the complex gain range of the 1st block (R1 to R4) } 39 1 to 4 .T& lw(108p) | cw(48p) | cw(48p) . { Bits of the code words of the complex gain range of the 2nd block (R5 to R8) } 39 5 to 8 .T& lw(108p) | cw(48p) | cw(48p) . { Check bits of two complex gain ranges (R9\ to\ R12) } 79 2, 4, 6, 8 .T& lw(108p) | cw(48p) | cw(48p) . { Check bits of the samples of the 1st block (R1 to R5) } blanc 40 79 blanc 1, 3, 4 1, 3 | \ .T& lw(108p) | cw(48p) | cw(48p) . { Check bits of the samples of the 2nd block (R6 to R10) } blanc 40 79 blanc 5, 7, 8 5, 7 | \ .T& lw(108p) | cw(48p) | cw(48p) . Signalling and check bits (S) 40 2 | \ | \ .T& lw(108p) | cw(48p) | cw(48p) . Data bits (D) 40 6 | \ | \ _ .TE .nr PS 9 .RT .ad r \fBTableau 5/J.43 [T5.43], p.17\fR .sp 1P .RT .ad b .RT .LP .sp 2 .ce \fBH.T. [T6.43]\fR .ce TABLE\ 6/J.43 .ps 9 .vs 11 .nr VS 11 .nr PS 9 .TS center box; cw(24p) sw(24p) sw(24p) sw(24p) sw(24p) sw(24p) sw(24p) sw(24p) | cw(36p) , c s s s | c s s c s | c | c s | c | ^ , c | c | c | c | c | c | c | c | ^ . { Bit number in sample n of block k } { Bit number in group\ 1 of frame N } N \(em 1 N \(em 2 k = 1 k = 2 k = 1 k = 2 n = 41\(em3 n = 41\(em1 n = 41\(em2 n = 41 n = 41\(em2 n = 41 n = 41\(em3 n = 41\(em1 _ .T& cw(24p) | lw(24p) | cw(24p) | lw(24p) | cw(24p) | lw(24p) | cw(24p) | lw(24p) | cw(36p) . 1.6\ 1.6 1.6 1.6\ 1 to 8 .T& cw(24p) | lw(24p) | cw(24p) | lw(24p) | cw(24p) | lw(24p) | cw(24p) | lw(24p) | cw(36p) . 2.7\ 2.7 2.7 2.7\ 9 to 16 .T& cw(24p) | lw(24p) | cw(24p) | lw(24p) | cw(24p) | lw(24p) | cw(24p) | lw(24p) | cw(36p) . 3.8\ 3.8 3.8 3.8\ 17 to 24 .T& cw(24p) | lw(24p) | cw(24p) | lw(24p) | cw(24p) | lw(24p) | cw(24p) | lw(24p) | cw(36p) . 4.9\ 4.9 4.9 4.9\ 25 to 32 .T& cw(24p) | lw(24p) | cw(24p) | lw(24p) | cw(24p) | lw(24p) | cw(24p) | lw(24p) | cw(36p) . 5.10 5 | 5 | 5.10 33 to 38 .T& cw(24p) | cw(24p) | cw(24p) | cw(24p) | cw(24p) | cw(24p) | cw(24p) | cw(24p) | cw(36p) . 1.6\ 1.6 1.6 1.6\ 41 to 48 .T& cw(24p) | cw(24p) | cw(24p) | cw(24p) | cw(24p) | cw(24p) | cw(24p) | cw(24p) | cw(36p) . 2.7\ 2.7 2.7 2.7\ 49 to 56 .T& cw(24p) | cw(24p) | cw(24p) | cw(24p) | cw(24p) | cw(24p) | cw(24p) | cw(24p) | cw(36p) . 3.8\ 3.8 3.8 3.8\ 57 to 64 .T& cw(24p) | cw(24p) | cw(24p) | cw(24p) | cw(24p) | cw(24p) | cw(24p) | cw(24p) | cw(36p) . 4.9\ 4.9 4.9 4.9\ 65 to 72 .T& cw(24p) | cw(24p) | cw(24p) | cw(24p) | cw(24p) | cw(24p) | cw(24p) | cw(24p) | cw(36p) . 5.10 5 | 5 | 5.10 73 to 78 .TE .IP N Number of the current frame: N = 0, \(+- | , \(+- | , . | | .IP 1 Number of the group in the frame: 1 = 1, 2, . | | , 8 .IP k Number of the block in the frame: k = 1, 2 .IP n Number of the sample in the block: n = 1, 2, . | | , 32 .nr PS 9 .RT .ad r \fBTableau 6/J.43 [T6.43], p.18\fR .sp 1P .RT .ad b .RT .LP .bp .sp 1P .LP 4.2.6 \fISynchronization of the 316 kbit/s stream\fR .sp 9p .RT .PP The 316 kbit/s stream is synchronized to the coder sampling frequency. .RT .sp 1P .LP 4.2.7 \fIFrame alignment of the 316/s stream\fR .sp 9p .RT .PP For the frame alignment the synchronizing properties of the Hamming code (12,8) are utilized and a special frame alignment signal is not employed. The signal R1\(hyR12 is used as a frame alignment signal. In the frame alignment signal receiver the relationships\ (2) from \(sc\ 4.2.3 are checked. The lock\(hyin time of such a frame alignment signal is equal to the lock\(hyin time of an 4\(hybit frame alignment signal. .RT .sp 2P .LP 4.3 \fIAsynchronous insertion of the 316 kbit/s signal into a 320\fR \fIkbit/s stream\fR .sp 1P .RT .sp 1P .LP 4.3.1 \fIFrame structure of the 320 kbit/s signal\fR .sp 9p .RT .PP The 320 kbit/s signal is composed of a data signal fo 316 kbit/s and a justification signal of 4\ kbit/s. The 320\ kbit/s stream is divided into groups of 80\ bits, 79\ bits being data bits and the 80th bit being the bit of the justification signal. .RT .sp 1P .LP 4.3.2 \fIJustification method\fR .sp 9p .RT .PP A method of positive\(hynegative justification with two\(hycommand control is used for the rate justification. The justification signal consists of justification commands and a data signal transmitted in the case of negative justification. The frame of the justification signal consists of 4\ bits. The justification commands are transmitted by three bits\ 111 or\ 000. The same commands are used for frame alignment of the justification signal. The 4th\ bit in the frame is used to transmit a data signal in the case of negative justification. .RT .sp 1P .LP 4.3.3 \fIAllocation of the justification signal in the frame of the\fR \fIprimary digital multiplex equipment\fR .sp 9p .RT .PP Bits of the justification signal are allocated in the frames of the primary digital multiplex equipment, which comprise the frame alignment signal in the channel time slot\ 0. .PP In the frame of the primary digital multiplex equipment, which comprises the justification bit, this bit is the last of all bits of the 320\ kbit/s signal which are allocated in the given frame, that is, the justification bit is the most remote bit from the frame alignment signal of the primary digital multiplex equipment. .RT .sp 1P .LP 4.4 \fIDigital interface between the encoder equipment and the insertion\fR \fIequipment\fR .sp 9p .RT .PP Under study. .RT .sp 1P .LP 4.5 \fIFault conditions and consequent actions\fR .sp 9p .RT .PP Under study. .RT .sp 2P .LP \fB5\fR \fBDigital interface between equipments using different coding standards\fR .sp 1P .RT .PP Under study. .RT .LP .rs .sp 5P .LP .bp .sp 2P .LP \fBRecommendation\ J.44\fR .RT .sp 2P .ce 1000 \fBCHARACTERISTICS\ OF\ EQUIPMENT\ FOR\ THE\ CODING\ OF\ \fR \fBANALOGUE\ MEDIUM | QUALITY\fR .EF '% Fascicle\ III.6\ \(em\ Rec.\ J.44'' .OF '''Fascicle\ III.6\ \(em\ Rec.\ J.44 %' .ce 0 .sp 1P .ce 1000 \fBSOUND\(hyPROGRAMME\ SIGNALS\ FOR\ TRANSMISSION\ ON\ 320\ kbit/s | CHANNELS\fR .FS Digital interface between Administrations which have adopted different systems should, if a bilateral agreement is not reached, operate at 384\ kbit/s (H\d0\u\ channel) and carry signals encoded according to Recommendation\ J.42, \(sc\ 4. Any necessary transcoding will be carried out by Administrations using the system specified in this Recommendation. .FE .ce 0 .sp 1P .ce 1000 \fI(Melbourne, 1988)\fR .sp 9p .RT .ce 0 .sp 1P .LP \fB1\fR \fBGeneral\fR .sp 1P .RT .PP 1.1 This Recommendation gives the characteristics of equipment for the coding of 7\ kHz monophonic analogue sound\(hyprogramme signals into a digital signal. Two monophonic digital signals can be combined to form a 320\ kbit/s signal having a structure specified in Recommendation\ J.43. .sp 9p .RT .PP 1.2 Equipment for coding of analogue sound\(hyprogramme signals, as specified in this Recommendation, can be: .LP a) A stand\(hyalone encoder/decoder with a digital interface at 320 kbit/s. The encoder operation and the decoder operation may be performed in two separate equipments or in the same equipment. .LP b) A combined encoder\(hymultiplex/decoder\(hydemultiplex with a digital interface at\ 1544 or 2048\ kbit/s. The encoder\(hymultiplex operation and the decoder\(hydemultiplex operation may be performed in two separate equipments or in the same equipment. .PP In case b) it is not mandatory to provide an external access at 320 kbit/s. .sp 2P .LP \fB2\fR \fBTransmission performance\fR .sp 1P .RT .PP The transmission performance per encoder/decoder pair shall be such that the limits specified in Recommendation\ J.23 (CCIR Recommendation\ 503) are exceeded by three encoder/decoder pairs connected in tandem at audio frequencies. .RT .sp 2P .LP \fB3\fR \fBMethod of encoding\fR .sp 1P .RT .PP 3.1 The encoding method is based on a uniformly quantized 14\(hybit per sample technique with differential\ 14 to 9.5\(hybit near instantaneous companding . .sp 9p .RT .PP 3.2 Fundamental characteristics of the equipment are: .LP Nominal\ audio\ bandwidth: 0.05 to 7 kHz. .LP Audio\ interface: see Recommendation J.23, \(sc 2. .LP Sampling\ frequency: 16 (1 \(+- 5 \(mu 10\uD\dlF261\u5\d) kHz. .LP Pre/de\(hyemphasis: Recommendation J.17 with 6.5 dB attenuation at 800 Hz. .sp 2P .LP \fB4\fR \fBCharacteristics of the equipment\fR .sp 1P .RT .sp 1P .LP 4.1 \fIIntroduction\fR .sp 9p .RT .PP The equipment described in this section uses the differential near\(hyinstantaneous method of companding in the coding of medium quality sound\(hyprogramme signals into digital form. .PP A two\(hystage process is used in the encoding equipment: .RT .LP a) conversion of a 7 kHz channel into a 158 kbit/s stream; .LP b) asynchronous insertion of two synchronous in\(hyphase 158 kbit/s streams into a 320\ kbit/s stream. .bp .PP \fINote\fR \ \(em\ The asynchronous insertion of two asynchronous in\(hyphase 158 kbit/s streams into a 320\ kbit/s stream allows the use, at the encoder location, of a clock not necessarily synchronous to the network clock. It can be advantageous when the encoder equipment and the insertion equipment are located in different places, and when the transmission link between them is unidirectional, .LP and the reverse processes in the decoding equipment. .sp 2P .LP 4.2 \fIConversion from 7 kHz to 158 kbit/s and constitution of the\fR \fI316 kbit/s signal\fR .sp 1P .RT .sp 1P .LP 4.2.1 \fIOverload level\fR .sp 9p .RT .PP The overload level for a sine\(hywave signal at the zero dB insertion loss frequency (2.1\ kHz) of the pre\(hyemphasis circuit is +12 or +15\ dBm0s. .RT .sp 1P .LP 4.2.2 \fICompanding\fR .sp 9p .RT .PP The same differential near\(hyinstantaneous companding procedure with a block of 32\ samples (2\ ms), as described in \(sc\ 4.2.2 of Recommendation\ J.43, is used. .RT .sp 1P .LP 4.2.3 \fIRange coding\fR .sp 9p .RT .PP The same range coding for a block of 32 samples (2 ms), as described in \(sc\ 4.2.3 of Recommendation\ J.43, is used. .RT .sp 1P .LP 4.2.4 \fISample error protection\fR .sp 9p .RT .PP The same sample error protection for a block of 32 samples (2 ms), as described in \(sc\ 4.2.4 of Recommendation\ J.43, is used. .RT .sp 1P .LP 4.2.5 \fI316 kbit/s channel frame\fR .sp 9p .RT .PP Two 7 kHz channels (C1 and C2) are contained in one 316 kbit/s stream. The frame structure of the 316\ kbit/s stream is described in \(sc\ 4.2.5 of Recommendation\ J.43. The first block (k\ =\ 1) of each frame corresponds to channel\ C1 and the second block (k\ =\ 2) of each frame corresponds to channel\ C2. .RT .sp 1P .LP 4.3 \fIAsynchronous insertion of the 316 kbit/s signal into a 320 kbit/s\fR \fIstream\fR .sp 9p .RT .PP See \(sc 4.3 of Recommendation J.43. .RT .sp 1P .LP 4.4 \fIDigital interface between the encoder equipment and the insertion\fR \fIequipment\fR .sp 9p .RT .PP Under study. .RT .sp 1P .LP 4.5 \fIFault conditions and consequent actions\fR .sp 9p .RT .PP Under study. .RT .sp 2P .LP \fB5\fR \fBDigital interface between equipments using different coding\fR \fBstandards\fR .sp 1P .RT .PP Under study. .RT .LP .rs .sp 13P .LP .bp .sp 1P .ce 1000 \v'3P' SECTION\ 5 .ce 0 .sp 1P .PP Section 5 has not yet been allocated. .sp 1P .RT .LP .rs .sp 40P .ad r \fBBlanc\fR .ad b .RT .LP .bp .LP \fBMONTAGE:\ \fR PAGE ... = PAGE BLANCHE .sp 1P .RT .LP .bp .sp 1P .ce 1000 \v'3P' SECTION\ 6 .ce 0 .sp 1P .ce 1000 \fBCHARACTERISTICS\ OF\ CIRCUITS\ FOR\ TELEVISION\ TRANSMISSIONS\fR .ce 0 .sp 1P .PP Former Recommendations J.61 and J.62 of Volume III\(hy2 of the \fIOrange Book\fR have been cancelled. The corresponding CCIR Recommendations have been combined into CCIR Recommendation\ 567, which refers to all television standards and colour systems. This Recommendation\ 567 and some other texts from CCIR may be very useful for television transmissions via cable, and reference is given to the following CCIR Recommendations, published in Volume\ XII (of the XV\ Plenary Assembly of the CCIR), ITU, Geneva,\ 1982. \v'4P' .sp 1P .RT .sp 2P .LP \fBRecommendation\ J.61\fR .RT .sp 2P .ce 1000 \fBTRANSMISSION\ PERFORMANCE\ OF\ TELEVISION\ CIRCUITS\fR .EF '% Fascicle\ III.6\ \(em\ Rec.\ J.61'' .OF '''Fascicle\ III.6\ \(em\ Rec.\ J.61 %' .ce 0 .sp 1P .ce 1000 \fBDESIGNED\ FOR\ USE\ IN\ INTERNATIONAL\ CONNECTIONS\fR .ce 0 .sp 1P .ce 1000 \fI(Geneva, 1982)\fR .sp 9p .RT .ce 0 .sp 1P .ce 1000 (See CCIR Recommendation 567) \v'4P' .sp 1P .RT .ce 0 .sp 1P .sp 2P .LP \fBRecommendation\ J.62\fR .RT .sp 2P .ce 1000 \fBSINGLE\ VALUE\ OF\ THE\ SIGNAL\(hyTO\(hyNOISE\ RATIO\fR .EF '% Fascicle\ III.6\ \(em\ Rec.\ J.62'' .OF '''Fascicle\ III.6\ \(em\ Rec.\ J.62 %' .ce 0 .sp 1P .ce 1000 \fBFOR\ ALL\ TELEVISION\ SYSTEMS\fR .ce 0 .sp 1P .ce 1000 \fI(Geneva, 1982)\fR .sp 9p .RT .ce 0 .sp 1P .sp 2P .LP (See CCIR Recommendation 568) .bp .sp 1P .RT .sp 1P .ce 1000 .ce 0 .sp 1P .sp 2P .LP \fBRecommendation\ J.63\fR .RT .sp 2P .ce 1000 \fBINSERTION\ OF\ TEST\ SIGNALS\ IN\ THE\ FIELD\(hyBLANKING\ INTERVAL\fR .EF '% Fascicle\ III.6\ \(em\ Rec.\ J.63'' .OF '''Fascicle\ III.6\ \(em\ Rec.\ J.63 %' .ce 0 .sp 1P .ce 1000 \fBOF\ MONOCHROME\ AND\ COLOUR\ TELEVISION\ SIGNALS\fR .ce 0 .sp 1P .ce 1000 \fI(Geneva, 1982)\fR .sp 9p .RT .ce 0 .sp 1P .ce 1000 (See CCIR Recommendation 473) \v'4P' .sp 1P .RT .ce 0 .sp 1P .sp 2P .LP \fBRecommendation\ J.64\fR .RT .sp 2P .ce 1000 \fBDEFINITIONS\ OF\ PARAMETERS\ FOR\ SIMPLIFIED\ AUTOMATIC\ MEASUREMENT\fR .EF '% Fascicle\ III.6\ \(em\ Rec.\ J.64'' .OF '''Fascicle\ III.6\ \(em\ Rec.\ J.64 %' .ce 0 .sp 1P .ce 1000 \fBOF\ TELEVISION\ INSERTION\ TEST\ SIGNALS\fR .ce 0 .sp 1P .ce 1000 \fI(Geneva, 1982)\fR .sp 9p .RT .ce 0 .sp 1P .ce 1000 (See CCIR Recommendation 569) \v'4P' .sp 1P .RT .ce 0 .sp 1P .sp 2P .LP \fBRecommendation\ J.65\fR .RT .sp 2P .ce 1000 \fBSTANDARD\ TEST\ SIGNAL\ FOR\ CONVENTIONAL\ LOADING .EF '% Fascicle\ III.6\ \(em\ Rec.\ J.65'' .OF '''Fascicle\ III.6\ \(em\ Rec.\ J.65 %' .ce 0 .sp 1P .ce 1000 \fBOF\ A\ TELEVISION\ CHANNEL\fR .ce 0 .sp 1P .ce 1000 \fI(Geneva, 1982)\fR .sp 9p .RT .ce 0 .sp 1P .ce 1000 (See CCIR Recommendation 570) \v'4P' .sp 1P .RT .ce 0 .sp 1P .sp 2P .LP \fBRecommendation\ J.66\fR .RT .sp 2P .ce 1000 \fBTRANSMISSION\ OF\ ONE\ SOUND\ PROGRAMME\ ASSOCIATED\ WITH\ ANALOGUE .EF '% Fascicle\ III.6\ \(em\ Rec.\ J.66'' .OF '''Fascicle\ III.6\ \(em\ Rec.\ J.66 %' .ce 0 .ce 1000 \fR \fB TELEVISION\ SIGNAL\ BY\ MEANS\ OF\ TIME\ DIVISION\ MULTIPLEX\fR .ce 0 .sp 1P .ce 1000 \fBIN\ THE\ LINE\ SYNCHRONIZING\ PULSE\fR .ce 0 .sp 1P .ce 1000 \fI(Geneva, 1982)\fR .sp 9p .RT .ce 0 .sp 1P .ce 1000 (See CCIR Recommendation 572) .sp 1P .RT .ce 0 .sp 1P .LP .bp .sp 1P .ce 1000 \v'3P' SECTION\ 7 .ce 0 .sp 1P .ce 1000 \fBGENERAL\ CHARACTERISTICS\ OF\fR \ \fBSYSTEMS\ FOR\ TELEVISION\ TRANSMISSION\fR .ce 0 .sp 1P .ce 1000 \fBOVER\ METALLIC\ LINES\ AND\ INTERCONNECTION\ WITH\ RADIO\(hyRELAY\ LINKS\fR .ce 0 .sp 1P .sp 2P .LP \fBRecommendation\ J.73\fR .FS Recommendations J.71 and J.72 of Volume III\(hy2 of the \fIOrange Book\fR have been deleted. .FE .RT .sp 2P .ce 1000 \fBUSE\ OF\ A\fR \ \fB12\(hyMHz\ SYSTEM\ FOR\ THE\ SIMULTANEOUS\ TRANSMISSION\ OF\fR .EF '% Fascicle\ III.6\ \(em\ Rec.\ J.73'' .OF '''Fascicle\ III.6\ \(em\ Rec.\ J.73 %' .ce 0 .sp 1P .ce 1000 \fBTELEPHONY\ AND\ TELEVISION\fR .ce 0 .sp 1P .ce 1000 \fI(amended at Geneva, 1964 and 1980)\fR .sp 9p .RT .ce 0 .sp 1P .PP The 12\(hyMHz system on 2.6/9.5\(hymm coaxial cable pairs and the 12\(hyMHz system on\ 1.2/4.4\(hymm coaxial pairs are defined in Recommendations\ G.332\ [1] and G.345\ [2] respectively. .sp 1P .RT .PP Any 12\(hyMHz system equipped for television transmission should be capable of transmitting the signals used in all the television systems defined in CCIR having a video bandwidth up to 5.5\ MHz if necessary, by means of the switching (in terminal equipments only) of certain components. .sp 2P .LP \fB1\fR \fBCarrier frequency\fR .sp 1P .RT .PP The CCITT recommends the use of a carrier frequency of 6799\ kHz with a tolerance of \(+- | 00\ Hz for the transmission of all the television signals indicated above. The video band transmitted over the cable should be 5.5\ MHz wide, whatever television system is to be used. The level recommended for this carrier has been defined for the interconnection points and is shown in Figures\ 1/J.73 and\ 2/J.73 (see Note\ 3 to these figures). .RT .sp 2P .LP \fB2\fR \fBModulation ratio\fR .sp 1P .RT .PP Amplitude modulation has to be used. The modulation ratio has to be higher than\ 100% (as indicated in Figure\ 3/J.73), so that, when the carrier is modulated by a signal corresponding to blanking level, its amplitude be equal to that of the carrier when it is modulated by a signal corresponding to the white level, assuming that the d.c. component is transmitted. .PP When a luminance bar (see CCIR Recommendation\ 567, Annex\ 1 to Part\ C, test signal element\ B2) is applied at a video junction point, the nominal peak voltage of the modulated carrier, at a point where the relative level for the television transmission is zero, should be as follows: .RT .LP \(em for white or blanking level, 0.387\ volt (i.e.\ the peak voltage of a sine\(hywave signal dissipating a power of 1\ mW in a resistance of 75\ ohms); .LP \(em for the synchronizing signals, 0.719\ volt (i.e.\ the peak voltage of a sine\(hywave signal dissipating a power of 3.45\ mW in a 75\ ohm resistance). .bp .LP .rs .sp 23P .ad r \fBFigure 1/J.73, p.\fR .sp 1P .RT .ad b .RT .LP .rs .sp 24P .ad r \fBFigure 2/J.73, p.\fR .sp 1P .RT .ad b .RT .LP .bp .LP .rs .sp 19P .ad r \fBFigure 3/J.73, p.\fR .sp 1P .RT .ad b .RT .sp 2P .LP \fB3\fR \fBVestigial\(hysideband shaping\fR .sp 1P .RT .PP The shaping of the vestigial\(hysideband signal has to be carried out entirely at the transmit point. Provisionally, the vestigial sideband should not exceed a width of 500\ kHz. Figure\ 4/J.73 shows the frequency arrangement recommended for television transmission over the 12\ MHz system. .RT .LP .rs .sp 10P .ad r \fBFigure\ 4/J.73, p.\fR .sp 1P .RT .ad b .RT .sp 2P .LP \fB4\fR \fBRelative power levels and interconnection at a frontier section\fR .sp 1P .RT .PP It is not possible to recommend relative power levels at the output of intermediate repeaters since they are very closely linked to the inherent design of each Administration's system. .PP When interconnection between two telephone systems is effected via a cable section that crosses a frontier, in accordance with Recommendation\ G.352\ [3], each Administration should accept, on the receiving side, the level conditions which normally apply to the incoming system used in the other country. It may be possible to comply with this condition simply by insertion of a correcting network at the receiving end. The repeater section crossing the frontier, should then be less than 4.5\ km long, the details being agreed directly between the Administrations concerned before the repeater stations are sited. .bp .PP Where a line is to be used alternatively for \*Qall\(hytelephony\*U or for \*Qtelephony\(hyplus\(hytelevision\*U, such a solution is not generally applicable. In this case, one of the frontier stations may act as a main station having the necessary types of pre\(hyemphasis and de\(hyemphasis networks to permit interconnection at flat points at the recommended levels. Figure\ 1/J.73 shows how this may be done in the general case and also shows how, at terminal stations, the same interconnections levels are used when connecting the line to telephony and television translating equipment. .PP However, if a common differential characteristic can be agreed for all types of 12\(hyMHz line, then free interconnection of the full line\(hybandwidth becomes possible, both nationally (e.g.\ between working and spare lines) and internationally (between national systems of different designs). This method leads to the simpler interconnection arrangement of Figure\ 2/J.73. .PP In this arrangement, the circuit is always lined up for \*Qall\(hytelephony\*U. For telephony\(hyplus\(hytelevision, the emphasis characteristic used for the \*Qall\(hytelephony\*U case is modified by the insertion, at the terminal equipment stations only, of differential pre\(hyemphasis and de\(hyemphasis networks additional to those used for \*Qall\(hytelephony\*U transmission. .RT .sp 2P .LP \fB5\fR \fBInterference\fR .sp 1P .RT .PP Recommendation\ J.61 (equal to CCIR\(hyRecommendation\ 567, Part\ D), indicates the overall values relative to the hypothetical reference circuit for television transmissions which are taken as objectives for design projects. .PP In the experience of certain Administrations, the weighted psophometric power can be distributed between the terminal equipment and the line in the ratio of 1\ to\ 4. .PP In particular, the Administration of the Federal Republic of Germany uses, for the\ 12\ MHz system, the following signal\(hyto\(hyweighted noise ratio: .RT .LP \(em for\ terminal\ modulation\ equipment: 70\ dB .LP \(em for\ terminal\ demodulation\ equipment: 64\ dB .LP \(em for\ a\ line\ 840\ km\ in\ length: 58\ dB .PP These values result in a signal\(hyto\(hynoise ratio of 52\ dB at the end of the reference circuit. .sp 2P .LP \fBReferences\fR .sp 1P .RT .LP [1] CCITT Recommendation \fI12\(hyMHz systems on standardized\fR \fI2.6/9.5\(hymm coaxial cable pairs\fR , Vol.\ III, Rec.\ G.332. .LP [2] CCITT Recommendation \fI12\(hyMHz systems on standardized 1.2/4.4\(hymm\fR \fIcoaxial cable pairs\fR , Vol.\ III, Rec.\ G.345. .LP [3] CCITT Recommendation \fIInterconnection of coaxial carrier systems of\fR \fIdifferent designs\fR , Vol.\ III, Rec.\ G.352. .sp 2P .LP \fBRecommendation\ J.74\fR .RT .sp 2P .ce 1000 \fBMETHODS\ FOR\ MEASURING\ THE\ TRANSMISSION\ CHARACTERISTICS\ OF\fR .EF '% Fascicle\ III.6\ \(em\ Rec.\ J.74'' .OF '''Fascicle\ III.6\ \(em\ Rec.\ J.74 %' .ce 0 .sp 1P .ce 1000 \fBTRANSLATING\ EQUIPMENTS\fR .ce 0 .sp 1P .PP \fB1\fR No special measuring method is necessary for the carrier. .sp 1P .RT .PP \fB2\fR An oscilloscope can be used, for example, to measure the modulation ratio. .sp 9p .RT .PP \fB3\fR No special method is recommended for measuring pre\(hyemphasis. .sp 9p .RT .PP \fB4\fR An oscilloscope can be used, for example, to measure the voltages at the input to the modulating equipment and the output from the demodulating equipment. .bp .sp 9p .RT .PP \fB5\fR The following is an example of a method which can be used to measure the random noise at the modulator output: .sp 9p .RT .LP The input and output video terminals of the modulator are closed with 75\ ohm resistances and the modulator is set to give an output carrier power of 1\ mW. The random noise power can then be measured with a selective measuring instrument, and the result is given relative to the video\(hyfrequency bandwidth for the television system concerned. .LP To measure noise produced by the demodulator, 1\ mW of carrier power is sent to its input, and the random noise at the output is measured at the output terminals with a selective measuring instrument. .LP This method can also be used to measure parasitic noise having a recurrent waveform. .PP \fINote\fR \ \(em\ Methods for measuring parasitic noise in television are being studied. \v'1P' .sp 2P .LP \fBRecommendation\ J.75\fR .RT .sp 2P .ce 1000 \fBINTERCONNECTION\ OF\ SYSTEMS\ FOR\ TELEVISION\ TRANSMISSION\ ON\fR .EF '% Fascicle\ III.6\ \(em\ Rec.\ J.75'' .OF '''Fascicle\ III.6\ \(em\ Rec.\ J.75 %' .ce 0 .sp 1P .ce 1000 \fBCOAXIAL\ PAIRS\ AND\ ON\ RADIO\(hyRELAY\ LINKS\fR .ce 0 .sp 1P .LP \fB1\fR \fBTelevision transmission only\fR .sp 1P .RT .PP Direct video transmission over long, e.g.\ more than about 15\ km, coaxial cables is unsatisfactory, because of the likelihood of picking up interference and the difficulties of low\(hyfrequency equalization; it is therefore necessary to transmit the television signal as a modulated carrier transmission, usually with a vestigial sideband. .PP On the other hand, the television signal can be transmitted directly in the baseband of a radio\(hyrelay system as a video signal. In general it is advantageous to do so, since this minimizes distortion and enables a better signal\(hyto\(hynoise ratio to be obtained as compared with a modulated signal with vestigial sideband, transmitted in the baseband. This procedure is recommended by the CCIR. .PP Interconnection between television channels on radio\(hyrelay and cable systems will therefore normally take place at video frequencies. .PP Levels and impedances at interconnection points should then conform to Recommendation\ J.61. .PP Exceptionally, in special cases, the video signal can be transmitted over short cables, or a vestigial\(hysideband television signal can be transmitted on short radio\(hyrelay links, to allow direct interconnection at line frequencies (radio\(hyrelay link baseband). Special arrangements may be necessary in such cases in respect of signal level, pre\(hyemphasis and pilots, to maintain the recommended standard of transmission performance. .RT .sp 2P .LP \fB2\fR \fBTelephony and television transmission, alternatively or\fR \fBsimultaneously, on coaxial pairs or radio\(hyrelay links\fR .sp 1P .RT .sp 1P .LP 2.1 \fIInterconnection between a coaxial cable system having alternative\fR \fItransmission of telephony and television and a radio\(hyrelay link with\fR \fIthe same alternative transmission\fR .sp 9p .RT .PP It is recommended that the following conditions should be met at the interconnection point: .RT .LP \(em For telephony transmission, the frequency arrangements, the relative power levels of the telephone channels and the frequency of the pilots should be as indicated in Recommendation\ G.423\ [1]. .LP \(em For television transmission, interconnection should generally be made at video frequencies. Levels and impedances at interconnection points should then conform to Recommendation\ J.61. .bp .sp 1P .LP 2.2 \fIInterconnection between a coaxial system having simultaneous\fR \fItelephony and television transmission and a radio\(hyrelay link with\fR \fIthe same simultaneous transmission\fR .sp 9p .RT .PP On all radio\(hyrelay links designed for such simultaneous transmission, it is intended to transmit video\(hyfrequency television signals in the lower part of the baseband and telephony signals in the upper part. Since these arrangements are incompatible with those which are recommended by the CCITT for simultaneous telephony and television transmission on coaxial cables (Recommendation\ J.73), it will normally be possible to consider interconnection at video frequencies only for the television channel, and interconnection at group, supergroup, mastergroup or supermastergroup points for telephony. .PP However, by agreement between the Administrations concerned, direct interconnection may be achieved, in special cases, on a short system (on cable or radio), by using a frequency allocation recommended for the other type of system. .RT .sp 2P .LP \fBReference\fR .sp 1P .RT .LP [1] CCITT Recommendation \fIInterconnection at the baseband frequencies\fR \fIof frequency\(hydivision multiplex radio\(hyrelay systems\fR , Vol.\ III, Fascicle\ III.2, Rec.\ G.423. .sp 2P .LP \fBRecommendation\ J.77\fR .FS Recommendation J.76 of Volume III\(hy2 of the \fIOrange Book\fR has been deleted. .FE .RT .sp 2P .ce 1000 \fBCHARACTERISTICS\ OF\ THE\ TELEVISION\ SIGNALS\fR .EF '% Fascicle\ III.6\ \(em\ Rec.\ J.77'' .OF '''Fascicle\ III.6\ \(em\ Rec.\ J.77 %' .ce 0 .sp 1P .ce 1000 \fBTRANSMITTED\ OVER\ 18\ MHz\ AND\ 60\(hyMHz\ SYSTEMS\fR .ce 0 .sp 1P .ce 1000 \fI(Geneva, 1980)\fR .sp 9p .RT .ce 0 .sp 1P .PP For television transmission on 18\ MHz and 60\ MHz systems, a modulation procedure has to be used which is independent of the structure of the signal to be transmitted. This is achieved by a reference carrier which defines the phase relationship between the transmit and receive side. .sp 1P .RT .PP The transmission channel is capable of transmitting the signals used in all those television systems defined by the CCIR, in accordance with Report\ 624\ [1]. .PP The requirements to be met by the 18\ MHz and 60\ MHz transmission systems are to be found in Recommendations\ G.334\ [2] and G.333\ [3]. .PP It is recommended that the following conditions be met: .RT .sp 2P .LP \fB1\fR \fBVestigial sideband shaping\fR .sp 1P .RT .PP The shaping of the vestigial sideband signal has to be carried out entirely at the transmit side. The vestigial sideband shall not exceed a width of 1\ MHz, i.e.\ the width of the Nyquist slope shall not exceed 2\ MHz. .RT .sp 2P .LP \fB2\fR \fBVideo pre\(hyemphasis\fR .sp 1P .RT .PP With regard to a more uniform loading of the coaxial line systems, it is recommended to use a video pre\(hyemphasis network. The video pre\(hyemphasis curve and the corresponding formula are shown in Figure\ 1/J.77. The video pre\(hyemphasis amounts to 9\ dB. .RT .sp 2P .LP \fB3\fR \fBNominal reference level of the modulated video signal\fR .sp 1P .RT .PP As a consequence of using a video pre\(hyemphasis network, it is necessary to define a reference level at a suitable video frequency. It is recommended that this reference level be derived from the level of a single sideband measured after the Nyquist filter when a 1\ kHz sine wave is transmitted, having a peak\(hyto\(hypeak amplitude of 0.7\ volt at the video interconnection point. The reference level is this measured level plus 6\ dB. The reference level is recommended to be +11\ dBm0. .bp .RT .LP .rs .sp 47P .ad r \fBFigure 1/J.77, p.\fR .sp 1P .RT .ad b .RT .LP .bp .sp 2P .LP \fB4\fR \fBAccuracy of carrier frequencies\fR .sp 1P .RT .PP The carrier frequency of the first modulation stage should have a tolerance not exceeding 11\ Hz. Tolerances of the carrier frequencies for the higher modulation stages can be ignored if either Recommendation\ G.225\ [4] is met, or if the carriers are derived from the relevant TV channel\(hypair pilots (see\ [5] and\ [6]). .RT .sp 2P .LP \fB5\fR \fBReference carrier\fR .sp 1P .RT .PP In order to enable accurate demodulation of the signal at the receive side, it is necessary to transmit a reference carrier. .PP The following characteristics are recommended: .RT .LP \(em carrier frequency of the first modulation stage corresponding to the video frequency of 0\ Hz; .LP \(em polarity negative, i.e. such that the amplitude of the modulated video signal is greater at black than at white; .LP \(em nominal power level: +10\ dBm0, independent of signal level. .sp 2P .LP \fB6\fR \fBLow frequency suppression\fR .sp 1P .RT .PP In order to prevent disturbance of the reference carrier by the low frequency components of the video signal, it is necessary to reduce the level of the low frequency components. A low frequency suppression of 18\ dB is recommended. The low frequency suppression curve and the corresponding formula are shown in Figure\ 1/J.77. \v'1P' .RT .sp 2P .LP \fBReferences\fR .sp 1P .RT .LP [1] CCIR Report \fICharacteristics of television systems\fR , Vol.\ XI, Report\ 624, ITU, Geneva,\ 1982. .LP [2] CCITT Recommendation \fI18\(hyMHz systems on standardized 2.6/9.5\(hymm\fR \fIcoaxial pairs\fR , Vol.\ III, Rec.\ G.334. .LP [3] CCITT Recommendation \fI60\(hyMHz systems on\fR \fIstandardized 2.6/9.5\(hymm coaxial cable pairs\fR , Vol.\ III, Rec.\ G.333. .LP [4] CCITT Recommendation \fIRecommendations relating to the\fR \fIaccuracy of carrier frequencies\fR , Vol.\ III, Rec.\ G.225. .LP [5] CCITT Recommendation \fI60\(hyMHz systems on\fR \fIstandardized\ 2.6/9.5\(hymm coaxial cable pairs\fR , Vol.\ III, Rec.\ G.333, \(sc\ 8.4, Note\ 2. .LP [6] CCITT Recommendation, \fI18\(hyMHz systems on standardized 2.6/9.5\(hymm\fR \fIcoaxial pairs\fR , Vol.\ III, Rec.\ G.334, \(sc\ 9.4.2, Note. .LP .rs .sp 15P .ad r \fBBlanc\fR .ad b .RT .LP .bp .sp 1P .ce 1000 \v'12P' \s12PART\ III \v'4P' .RT .ce 0 .sp 1P .ce 1000 \fBSUPPLEMENTS\ TO\ H\ AND\ J\ SERIES\ RECOMMENDATIONS\fR .EF '% \ \ \ ^'' .OF ''' \ \ \ ^ %' .ce 0 .sp 1P .LP .rs .sp 35P .ad r \fBBlanc\fR .EF '% \ \ \ ^'' .OF ''' \ \ \ ^ %' .ad b .RT .LP .bp .LP \fBMONTAGE:\fR \ PAGE 234 = PAGE BLANCHE .sp 1P .RT .LP .bp .sp 2P .LP \fBSupplement\ No.\ 5\fR .RT .sp 2P .ce 1000 \fBMEASUREMENT\ OF\ THE\ LOAD\ OF\ TELEPHONE\ CIRCUITS\fR .EF '% Fascicle\ III.6\ \(em\ Suppl.\ No.\ 5'' .OF '''Fascicle\ III.6\ \(em\ Suppl.\ No.\ 5 %' .ce 0 .sp 1P .ce 1000 \fBUNDER\ FIELD\ CONDITIONS\fR .ce 0 .sp 1P .ce 1000 (Referred to in Recommendations\ G.223 and\ H.51 this supplement is to be .sp 9p .RT .ce 0 .sp 1P .ce 1000 found on page 295 of Fascicle III.2 of the \fIRed Book\fR , Geneva, 1985) \v'1P' .ce 0 .sp 1P .sp 2P .LP \fBSupplement\ No.\ 12\fR .RT .sp 2P .ce 1000 \fBINTELLIGIBILITY\ OF\ CROSSTALK\ BETWEEN\ TELEPHONE\ AND\fR .EF '% Fascicle\ III.6\ \(em\ Suppl.\ No.\ 12'' .OF '''Fascicle\ III.6\ \(em\ Suppl.\ No.\ 12 %' .ce 0 .sp 1P .ce 1000 \fBSOUND\(hyPROGRAMME\ CIRCUITS\fR .ce 0 .sp 1P .ce 1000 (Referred to in Recommendation\ J.32; this supplement is to be found .sp 9p .RT .ce 0 .sp 1P .ce 1000 on page\ 610 of Fascicle III.2 of the \fIGreen\ Book\fR , Geneva,\ 1972.) \v'1P' .ce 0 .sp 1P .LP \fR .sp 2P .LP \fBSupplement\ No.\ 16\fR .RT .sp 2P .ce 1000 \fBOUT\(hyOF\(hyBAND\ CHARACTERISTICS\ OF\ SIGNALS\ APPLIED\fR .EF '% Fascicle\ III.6\ \(em\ Suppl.\ No.\ 16'' .OF '''Fascicle\ III.6\ \(em\ Suppl.\ No.\ 16 %' .ce 0 .sp 1P .ce 1000 \fBTO\ LEASED\ TELEPHONE\(hyTYPE\ CIRCUITS\fR .ce 0 .sp 1P .ce 1000 (Referred to in Recommendation H.51; this Supplement is to be found on page 191 .sp 9p .RT .ce 0 .sp 1P .ce 1000 of Fascicle III.4 of the \fIRed Book\fR , Geneva, 1985) \v'1P' .ce 0 .sp 1P .LP .bp