.rs .\" Troff code generated by TPS Convert from ITU Original Files .\" Not Copyright ( c) 1991 .\" .\" Assumes tbl, eqn, MS macros, and lots of luck. .TA 1c 2c 3c 4c 5c 6c 7c 8c .ds CH .ds CF .EQ delim @@ .EN .nr LL 40.5P .nr ll 40.5P .nr HM 3P .nr FM 6P .nr PO 4P .nr PD 9p .po 4P .rs \v | 5i' .LP \fBMONTAGE:\ \fR REC.\ G.956 EN T\* | TE DE CETTE PAGE .IP \v'15P' \fB9.6\ Digital section and digital transmission systems for ISDN customer access\fR .sp 1P .RT .sp 2P .LP \fBRecommendation\ G.960\fR .RT .sp 2P .sp 1P .ce 1000 \fBDIGITAL\ SECTION\ FOR\ ISDN\ BASIC\ RATE\ ACCESS\fR .EF '% Fascicle\ III.5\ \(em\ Rec.\ G.960'' .OF '''Fascicle\ III.5\ \(em\ Rec.\ G.960 %' .ce 0 .sp 1P .ce 1000 \fR \fI(Melbourne, 1988)\fR .sp 9p .RT .ce 0 .sp 1P .LP \fB1\fR \fBGeneral\fR .sp 1P .RT .sp 1P .LP 1.1 \fIScope\fR .sp 9p .RT .PP This Recommendation describes the characteristics of a digital section for the ISDN basic rate access between the user network interface (at T\ reference point, defined in Recommendation\ I.411) and the local exchange (at V\d1\u\ reference point defined in Recommendation\ Q.512) supporting the recommended channel structure 2B\ +\ D and the required additional functions. .PP In this Recommendation and unless otherwise indicated, the term TE is used to indicate terminating layer\ 1 aspects of\ TE1, TA and\ NT2 functional groups. .PP When the term TE indicates terminating layer 1 aspects of TE1, then according to Figure\ 2/I.411, the S\ and T\ reference points coincide. .PP The terminology used in this Recommendation is very specific and not contained in the relevant terminology Recommendations. Therefore Annex\ B to this Recommendation provides terms and definitions used in this Recommendation. .RT .sp 1P .LP 1.2 \fIConfiguration\fR .sp 9p .RT .PP Figure 1/G.960 shows the boundaries of the digital section in relation to the digital system definition. .RT .PP The concept of the digital section is used in order to allow a functional and procedural description and a definition of the network requirements. .PP Note that reference point T and V\d1\uare not identical and therefore the digital section is not symmetric. .PP The concept of a digital transmission system is used in order to describe the characteristics of a implementation, using a specific medium, in support of the digital section. .PP \fINote\fR \ \(em\ The T and V reference points are defined in Recommendations\ I.411 and\ Q.512. .bp .RT .LP .rs .sp 19P .ad r \fBFigure 1/G.960, p.1\fR .sp 1P .RT .ad b .RT .sp 1P .LP 1.3 \fIApplication\fR .sp 9p .RT .PP The basic access digital section may be applied as given in Figure\ 2/G.960 for: .RT .LP \(em direct access to the local exchange (V\d1\u\(hyreference point); .LP \(em access via a basic access multiplex equipment (V\d4\u\(hyinterface) to the local exchange; .LP \(em access via a basic access concentrator (V\d2\u\(hyinterface) to the local exchange; .sp 1P .LP 1.4 \fIAbbreviations\fR .sp 9p .RT .PP A number of abbreviations are used in this Recommendation. Some of them are commonly used in the ISDN reference configuration while others are created only for this Recommendation. The last one are given in the following: .RT .LP C\dV\\d1\u Control Channel at V\d1\ureference point .LP DS Digital Section .LP FE Function Element used between ET and LT .LP FII Failure Indication Information .LP INFO Information element defined at the user network interface .LP SIG Signal between LT an NT1 .sp 2P .LP \fB2\fR \fBModelling and relationship between the digital section\fR \fBand the ET\fR .sp 1P .RT .PP The general model shown in Figure 3/G.960 depicts the whole ISDN customer access layer 1 and adjacent entities and provides the basis to describe the functions performed by the digital section and those performed by TE, ET and system management and how various functions are grouped. In particular, according to this model the activation/deactivation procedures and maintenance functions specified in this Recommendation are not confined to functions performed by the digital section but include functions associated with\ ET layer\ 1. .bp .RT .LP \fR .rs .sp 36P .ad r \fBFigure 2/G.960 p.2\fR .sp 1P .RT .ad b .RT .PP This model includes primitive procedures between ET layer 1, ET\ layer\ 2 and system management: .RT .LP i) I.430 to I.440/I.441 interactions between ET layer 1 and ET layer 2, and ET layer\ 1 and system management based on\ PH and\ MPH primitives, respectively, as defined in Recommendation\ I.430. These interactions are for the support of functions specified in Recommendations\ I.440 and\ I.441; .LP ii) interactions between ET layer 1 and system management for the support of functions associated with the digital section, based on MPH primitives. .PP The primitive procedures within TE comply with the specification according to Recommendation\ I.430. .PP This model does not constrain layer 1 arrangements between LT and NT1, (it is also applicable to remote access as shown in Figure\ 2/G.960), or the digital transmission system technology. .bp .RT .LP .rs .sp 28P .ad r \fBFigure 3/G.960, p.\fR .sp 1P .RT .ad b .RT .sp 2P .LP \fB3\fR \fBFunctions\fR .sp 1P .RT .PP Figure 4/G.960 shows the functions which have to be supported by the basic access digital section. .RT .sp 1P .LP 3.1 \fIB channel\fR .sp 9p .RT .PP This function provides, for each direction of transmission, two independent 64\ kbit/s channels for use as B\ Channels (as defined in Recommendation\ I.412). .RT .sp 1P .LP 3.2 \fID channel\fR .sp 9p .RT .PP This function provides, for each direction of transmission, one D\ Channel at a bit rate of 16 kbit/s (as defined in Recommendation\ I.412). .RT .sp 1P .LP 3.3 \fIBit timing\fR .sp 9p .RT .PP This function provides bit (signal element) timing to enable the receiving equipment to recover information from the aggregate bit stream. Regarding the V\d1\ureference point, the bit timing function is used for both transmit and receive data. .RT .sp 1P .LP 3.4 \fIOctet timing\fR .sp 9p .RT .PP This function provides 8 kHz octet timing for the B Channels. .bp .RT .LP .rs .sp 28P .ad r \fBFigure 4/G.960, p.4\fR .sp 1P .RT .ad b .RT .sp 2P .LP 3.5 \fIActivation\fR .sp 1P .RT .sp 1P .LP 3.5.1 \fIActivation from ET\fR .sp 9p .RT .PP This function places all the functions of the digital section into a normal operating mode and supports the activation of the interface at the T reference point according to Recommendation\ I.430. This takes into account: .RT .LP \(em power down mode; .LP \(em initial power up; .LP \(em a failure condition. .PP The procedures and exchange of information are described in \(sc 5 of this Recommendation. .PP An activation should be possible to a state which allows maintenance actions to be performed in the digital section even when there is no customer equipment connected to the T\ reference point. .PP In the case of a basic access digital section making use of a digital transmission system for a metallic line one additional mode of operation may be applied for activation/deactivation, which is to activate/deactivate the digital section only. This is optional. .RT .sp 1P .LP 3.5.2 \fIRequest for activation from TE\fR .sp 9p .RT .PP This function supports activation of the digital section and of the interface at the T\ reference point according to Recommendation\ I.430. .PP These functions are conveyed by the C\dV\\d1\uchannel (see \(sc\ 7). .bp .RT .sp 1P .LP 3.6 \fIDeactivation\fR .sp 9p .RT .PP This function is specified in order to permit the interface at the T\ reference point and the digital section to be placed in a low power consumption mode. The procedures and exchange of information are described in \(sc\ 5 of this Recommendation. .PP Deactivation should be initiated only by the exchange (ET). .PP This function is conveyed by the C\dV\\d1\uchannel (see \(sc 7). .RT .sp 1P .LP 3.7 \fIPower feeding\fR .sp 9p .RT .PP This function provides for remote power feeding of NT1 and optionally the TE via the user network interface in accordance with Recommendation\ I.430, \(sc\ 9. .RT .sp 1P .LP 3.8 \fIOperation and maintenance\fR .sp 9p .RT .PP This function supports required actions and information for operating and maintaining the digital section controlled by the ET as defined in Recommendation\ I.603. .PP Four categories of functions have been identified: .RT .LP \(em commands regarding LT, regenerator, or NT1; .LP \(em information from LT, regenerator, or NT1; .LP \(em indications of fault conditions; .LP \(em control of digital section power feeding. .PP These functions are conveyed by the C\dV\\d1\uchannel (see \(sc 7). .sp 2P .LP \fB4\fR \fBNetwork performance\fR .sp 1P .RT .sp 1P .LP 4.1 \fIAvailability\fR .sp 9p .RT .PP The definition of availability is given in Annex A of Recommendation\ G.821. The availability objective of the digital section should be consistent with the availability requirement for the hypothetical reference digital section as given in Recommendations\ G.801 and\ I.350. .RT .sp 1P .LP 4.2 \fISignal transfer delay\fR .sp 9p .RT .PP Signal transfer delay is specified for B Channels and is defined as absolute signal delay between\ T and\ V\d1\ureference points for each direction of transmission. The value is for further study. The relevant Recommendations have to be taken into account (e.g.\ signal transmission delay when the signal represents speech must be taken into account as one component of the end\(hyto\(hyend delay requirement of Recommendation\ G.114). .RT .sp 1P .LP 4.3 \fIError performance\fR .sp 9p .RT .PP Error performance must be consistent with the requirements given in Recommendation\ G.821. .RT .sp 2P .LP 4.4 \fIJitter\fR .sp 1P .RT .sp 1P .LP 4.4.1 \fIOutput/input jitter at T reference point\fR .sp 9p .RT .PP The requirements are defined in \(sc 8 of Recommendation I.430. .RT .sp 1P .LP 4.4.2 \fIJitter at V\fI .sp 9p .RT .EF '% \fI1\ reference\ point'' .OF '''\fI1\ reference\ point %' .PP The input jitter limits are for further study. .RT .sp 2P .LP \fB5\fR \fIActivation/deactivation\fR .sp 1P .RT .sp 1P .LP 5.1 \fIFunctional capabilities\fR .sp 9p .RT .PP The digital section provides the layer 1 signalling capability and the necessary procedures to enable: .RT .sp 1P .LP 5.1.1 \fICustomer equipment at the user side of reference point T\fR .sp 9p .RT .LP to activate the layer 1 of the user\(hynetwork interface at reference point\ T and, if not already activated, the digital section. .bp .sp 1P .LP 5.1.2 \fIEquipment at the network side of V\fI .sp 9p .RT .EF '% \fI1\ reference\ point\ to'' .OF '''\fI1\ reference\ point\ to %' .LP a) activate: .LP 1) the layer 1 of the user\(hynetwork interface at reference point\ T and, if not already activated, the digital section (this activation is related to call control), or .LP 2) the digital section only (this activation is related to controlling the configuration of the access; it is a network opinion), .LP b) deactivate: .LP 1) the layer 1 of the user\(hynetwork interface at reference point\ T and the digital section, or .LP 2) the layer 1 of the user\(hynetwork interface at reference point\ T only. .PP The functional capabilities defined in \(sc 5.1.2 | ) | ) allow maintenance actions in the digital section which do not impact the deactivated user\(hynetwork interface at reference point\ T to be performed and make provision for the implementation of a non\(hytransparent loopback\ 2. If required in some applications, they also permit the digital section to be placed in a mode where the full information transfer capability is available while the user\(hynetwork interface at reference point\ T remains deactivated. .PP The procedures for the activation or deactivation of the layer 1 of the user\(hynetwork interface at reference point\ T comply with the Recommendation\ I.430, \(sc\ 6.2. These procedures are based on a repertoire of INFO signals as defined in Recommendation\ I.430 (Table\ 2/I.430). .PP The procedures at V\d1\ureference point are based on a repertoire of function elements (FEs). These FEs have specific relationships to primitives between the ET layer\ 1 and ET layer\ 2, and ET layer\ 1 and system management for the activation or deactivation of the layer\ 1 of the user\(hynetwork interface in accordance with Recommendation\ I.430, \(sc\ 6.2 and Recommendation\ I.440 and\ I.441. The means for defining these interactions are the primitive procedures (see Figure\ 5/1.430) based on a repertoire of PH\(hy and MPH\(hyprimitives. .RT .sp 2P .LP 5.2 \fIModelling\fR .sp 1P .RT .sp 1P .LP 5.2.1 \fIGeneral\fR .sp 9p .RT .PP The model for activation/deactivation procedures is given in \(sc\ 2. .PP It is recognized that activation/deactivation is a process between customer equipment and local exchange requiring appropriate functionality at both ends. The model contained in \(sc\ 2 includes the functional blocks relevant to activation/deactivation and depicts the primitives related to the activation/deactivation procedures. .RT .sp 1P .LP 5.2.2 \fIPartitioning of functions\fR .sp 9p .RT .PP Recommendation I.430 defines the network side of the user\(hynetwork interface at reference point\ T as one functional block which supports the layer\ 1 activation/deactivation procedures across the T\ reference point and the primitive procedures at the ET layer\ 1/ET layer\ 2 boundary and ET layer\ 1/system management boundary. This block includes the functional groupings NT1, LT and ET layer\ 1. .PP This concept is described in terms of a state machine, called the G state machine in Recommendation\ I.430. .PP In order to describe the relationship between signals across the user\(hynetwork interface at reference point\ T and function elements across reference point\ V\d1\u, and the relationship between function elements across reference point\ V\d1\uand primitives, two state machines are defined. One in the digital section (DS virtual state machine), and one at the network side of the V\d1\ureference point (ET layer\ 1 virtual state machine). Figure\ 5/G.960 illustrates this approach. .PP In addition to primitives defined in Recommendation I.430 and I.441 related to call control, Figure\ 5/G.960 also introduces a new set of primitives related to configuration control and the control of loopbacks. Partitioning of activation/deactivation procedures between two state machines is used for the convenience of easy and accurate description. The ET layer\ 1 state machine is to be viewed as virtual, not intended to imply any particular implementation. .RT .PP However, in order to implement a customer access the virtual DS state machine has to be partitioned further. Figure 6/G.960 shows the partition of the DS state machine into NT1 state machine (NT\(hystates) and LT state machine (LT\(hystates). .PP The NT1 state machine supports user\(hynetwork interface procedures in accordance with Recommendation\ I.430 based on the INFOs, and interacts with the LT state machine by means of a signal repertoire (SIGs) which has to be supported by the line transmission system. The LT state machine interacts with the ET layer\ 1 state machine by means of a set of function elements (FEs). The ET layer\ 1 state machine contains those states which represent the local exchange view of the status of the interface at reference point\ T and the digital section. It supports the already specified primitive procedures to provide services to ET layer\ 2 and system management in accordance with Recommendation\ I.430, and additional primitive procedures for the support of functions associated with the digital section. .bp .RT .LP .rs .sp 23P .ad r \fBFigure 5/G.960, p.5\fR .sp 1P .RT .ad b .RT .PP Figure 6/G.960 provides information for the description of the transmission system which is given in Recommendation\ G.961. .LP .rs .sp 23P .ad r \fBFigure 6/G.960, p.\fR .sp 1P .RT .ad b .RT .LP .bp .sp 1P .LP 5.2.3 \fILocation of timers T1 and T2\fR .sp 9p .RT .PP In the following description of the DS and ET layer 1 state machines, timer T1 will be associated with ET layer\ 1 (ET layer\ 1 state machine) while timer T2 will be associated with the digital section (DS state machine). .PP The association of timer T1 with layer 1 of the ET is applied for the convenience of easy description but may be implemented anywhere while being functional part of the ET. The exact location of timer T2 within the digital section does not impact the description of the DS state machine. .RT .sp 1P .LP 5.3 \fIActivation/deactivation procedures\fR .sp 9p .RT .PP The procedures allow the activation/deactivation of the user\(hynetwork interface at reference point\ T. The activation may be invoked by either side while deactivation may only be invoked by the network. The overall activation/deactivation procedures can be divided into three classes: .RT .LP a) basic procedures for call control used to activate the layer\ 1 of the user\(hynetwork interface at the T\ reference point and if not already activated, the digital section; .LP b) procedures to control loopbacks; .LP c) procedures to control the configuration. .sp 2P .LP 5.3.1 \fIBasic characteristics of the procedures\fR .sp 1P .RT .sp 1P .LP 5.3.1.1 \fIPriority\fR .sp 9p .RT .PP Priority refers to contention resolution between activation/deactivation requests which have been invoked concurrently. .PP If contention between conflicting activation/deactivation requests from layer\ 2 and system management occurs it is resolved in the ET layer\ 1 state machine, which will then pass to the V\d1\ureference point a coordinated set of Function Elements (FEs). Table\ 1/G.960 shows the ET layer\ 1 state machine priority order. .RT .ce \fBH.T. [T1.960]\fR .ce TABLE\ 1/G.960 .ce \fBPriority order of request in the ET layer 1 state machine\fR .ps 9 .vs 11 .nr VS 11 .nr PS 9 .TS center box; cw(180p) | cw(48p) . Type of request Priority order _ .T& lw(180p) | lw(48p) . Deactivation request 3 (highest) .T& lw(180p) | lw(48p) . Loopback 2 .T& lw(180p) | lw(48p) . { Call control activation request } 1 .T& lw(180p) | lw(48p) . { Digital section only activation/deactivation request from the ET side } 0 (lowest) _ .TE .nr PS 9 .RT .ad r \fBTable 1/G.960 [T1.960], p.\fR .sp 1P .RT .ad b .RT .PP If contention between conflicting activation/deactivation requests from ET side and user side occurs it is resolved in the DS state machine. Table\ 2/G.960 shows the DS state machine priority order. .ce \fBH.T. [T2.960]\fR .ce TABLE\ 2/G.960 .ce \fBPriority order of requests in the DS state machine\fR .ps 9 .vs 11 .nr VS 11 .nr PS 9 .TS center box; cw(180p) | cw(48p) . Type of request Priority order _ .T& lw(180p) | lw(48p) . { Request from ET side except digital section only activation } 2 (highest) .T& lw(180p) | lw(48p) . { Call control activation request from user side } 1 .T& lw(180p) | lw(48p) . { Digital section only activation/deactivation request from the ET side } 0 (lowest) _ .TE .nr PS 9 .RT .ad r \fBTable 2/G.960 [T2.960], p.\fR .sp 1P .RT .ad b .RT .LP .bp .sp 1P .LP 5.3.1.2 \fISystem management\fR .sp 9p .RT .PP Some assumptions related to the system management are described in Annex\ A. .RT .sp 1P .LP 5.3.1.3 \fILoopbacks\fR .sp 9p .RT .PP In case a transparent loopback 2 is applied, the NT1 shall send INFO\ 4 frames toward the user with the D\(hyecho\(hychannel set to binary ZERO. .PP With a transparent loopback 1, the NT1 (when able to activate the user\(hynetwork interface at the T reference point) shall send INFO\ 4 frames toward the user with the D\(hyecho\(hychannel set to binary ZERO or operating normally. .RT .sp 1P .LP 5.3.1.4 \fIProtection of layer 2 frames\fR .sp 9p .RT .PP According to Recommendation I.430 \(sc 6.2.6.1 a TE is allowed to take up to 100\ ms to synchronize on INFO\ 2, no lower time limit is defined. The different time each TE may take to synchronize on INFO\ 2 affects the offering of an incoming call in layer\ 1 multiple terminal arrangements. The fastest TE notifies to the network that the access is activated and the message offering the incoming call (SETUP) may be transmitted (TE ready to receive the message) while other TEs are not yet ready to receive the message. .PP This could result in the slow TEs loosing all or part of the incoming messages (layer\ 2 frames). .PP The protection mechanism is for further study. .RT .sp 1P .LP 5.3.1.5 \fIStructure of the tables\fR .sp 9p .RT .PP Both the DS state transition table and the ET layer 1 state transition table are structured such that the three classes of the activation/deactivation procedures described at the beginning of \(sc\ 5.3 are clearly separated. This allows implementation of the basic procedure only. .RT .sp 1P .LP 5.3.1.6 \fITransmission of INFO 2\fR .sp 9p .RT .PP In the following procedures two different internal events of the digital section are considered to start transmission of INFO\ 2: .RT .LP a) the transmission system is synchronized in the direction LT to NT1 .LP b) the transmission system is synchronized in both directions of transmission (see Note\ 2, Table\ 3/G.960) .sp 2P .LP 5.4 \fIDescription of the state transtition tables\fR .sp 1P .RT .sp 1P .LP 5.4.1 \fIDescription of the DS state transition table\fR .sp 9p .RT .sp 1P .LP 5.4.1.1 \fIDigital section states (DS\(hystates)\fR .sp 9p .RT .PP Hereafter are defined the states that the digital section may enter as a result of: INFOs received across reference point\ T, function elements (FEs) received across reference point\ V\d1\u, or internal events. .PP The DS\(hystates are classified according to the functionality they support as follows: .RT .LP i) DS 1.X states for the support of functionality according to Recomendation\ I.430; .LP ii) DS 2.X states for the support of functionality related to loopbacks (these states complement DS\ 1.X states); .LP iii) DS 3.X states for the support of functionality related to digital section only activation/deactivation (these states complement DS 1.X states). .PP The X represents the specific state within each mode. Some values of X are not used in mode\ 2 and\ 3 in order to have a consistent use of them. .bp .sp 1P .LP 5.4.1.1.1\ \ State DS 1.0 (fully deactivated): in this state state, the digital section is in a non\(hyoperational mode and as seen from the user side of reference point\ T, the network side is in state G1 according to Recommendation\ I.430 \(sc\ 6.2.1.2.1. .sp 9p .RT .LP 5.4.1.1.2\ \ State DS 1.1 (pending activation access): this transitional state is entered when an activation of the access was requested by the network (by means of either the PH\(hy or MPH\(hyACTIVATE\(hyREQUEST primitive) or the user (by means of INFO 1\ across T\ reference point) while the digital section was in the state DS\ 1.0. An awake process takes place to establish the digital section conditions which allow the transmission of INFO\ 2 across T\ reference point. As seen from the user side of reference point\ T, the network side is in state G1 according to Recommendation\ I.430 \(sc\ 6.2.1.2.1. .LP 5.4.1.1.3\ \ State DS 1.2 (transitional state access activation): when entering this transitional state the network initiates transmission of INFO\ 2 across reference point while waiting for the digital section to be fully synchronized and the receipt of INFO\ 3. As seen from the user side of reference point\ T, the network side is in state G2 according to Recommendation\ I.430 \(sc\ 6.2.1.2.2. .LP 5.4.1.1.4\ \ State DS 1.3 (digital section fully activated): in this transitional state, the digital section is synchronized in both directions of transmission and the network sends INFO\ 2 across T\ reference point while waiting for INFO\ 3. As seen from the user side of reference point\ T, the network side is in state\ G2 according to Recommendation\ I.430 \(sc\ 6.2.1.2.2. This state is also entered if loss of synchronization occurs at reference point\ T while in the state DS\ 1.5. .LP 5.4.1.1.5\ \ State DS 1.5 (interface at T activated): this is the normal active stable state where the layer\ 1 service is available to the higher layers. The network sends INFO\ 4 across\ T reference point and as seen from the user side, the network side is in state\ G3 according to Recommendation\ I.430 \(sc\ 6.2.1.2.3. .LP 5.4.1.1.6\ \ State DS 1.6 (pending deactivation access): this transitional state is entered if the system management instructed the digital section to deactivate the access. As seen from the user side of reference point\ T, the network side is in state G4 according to Recommendation\ I.430 \(sc\ 6.2.1.2.4. .LP 5.4.1.1.7\ \ State DS 1.7 (transitional state access deactivation): in this transitional state, the interface at reference point T is already deactivated. The deactivation of the digital section is in progress. As seen from the user side of reference point\ T, the network side is in state G1 according to Recommendation\ I.430 \(sc\ 6.2.1.2.1. .LP 5.4.1.1.8\ \ State DS 1.8 (transitional state access deactivation): in this transitional state, the digital section is already deactivated. The deactivation of the interface at reference point\ T is in progress. As seen from the user side of reference point\ T, the network side is in state\ G4 according to Recommendation\ I.430 \(sc\ 6.2.1.2.4. .LP 5.4.1.1.9\ \ States DS 2.X: for further study. .LP 5.4.1.1.10\ \ State DS 3.1 (pending activation digital section only): this transitional state is entered when an activation of the digital section only was requested by the network (by means of the MPH\(hyDIGITAL SECTION ACTIVATE\(hyREQUEST primitive, MHP\(hyDSAR). The digital section was previously in the state DS\ 1.0 or a deactivation of the access was previously in progress. As seen from the user side of reference point\ T, the network side is in state G1 according to Recommendation\ I.430 \(sc\ 6.2.1.2.1. .LP 5.4.1.1.11\ \ State DS 3.2 (transitional state digital section activation): this transitional state is entered when an activation of the digital section only was requested by the network (by means of the MPH\(hyDIGITAL SECTION ACTIVATE\(hyREQUEST primitive, MPH\(hyDSAR). The deactivation of the access was previously in progress. As seen from the user side of reference point\ T, the network side is in state G4 according to Recommendation\ I.430 \(sc\ 6.2.1.2.4. .LP 5.4.1.1.12\ \ State DS 3.3 (digital section only activated): in this stable state, the digital section is synchronized in both directions of transmission and this has been notified to the system management by means of the MPH\(hyDIGITAL SECTION ACTIVATE\(hyINDICATION primitive (MPH\(hyDSAI). The network sends INFO\ 0 across T\ reference point. As seen from the user side of reference point\ T, the network side is in state\ G1 according to Recommendation\ I.430 \(sc\ 6.2.1.2.1. .LP 5.4.1.1.13\ \ State DS 3.4 (pending activation interface): this transitional state is entered when an activation of the interface was requested by the network (by means of either the PH\(hy or MPH\(hyACTIVATE\(hyREQUEST primitive) or the user (by means of INFO\ 1 across the T\ reference point) while the digital section was already in the activated state, state DS\ 3.3. The network immediately transmits INFO\ 2 across the T\ reference point. As seen from the user side of reference point\ T, the network side is in state G2 according to Recommendation\ I.430 \(sc\ 6.2.1.2.2. .bp .LP 5.4.1.1.14\ \ State DS 3.6 (pending deactivation interface): this transitional state is entered if the system managemnt instructed the digital section to deactivate the interface at reference point\ T but to remain activated. As seen from the user side of reference point\ T, the network side is in state\ G4 according to Recommendation\ I.430 \(sc\ 6.2.1.2.4. .sp 1P .LP 5.4.1.2 \fIRepertoire of signals across the user\(hynetwork interface at the\fR \fIT\ reference point\fR .sp 9p .RT .PP The definition of INFO signals is contained in Recommendation\ I.430 \(sc\ 6.2.2. .RT .sp 1P .LP 5.4.1.3 \fIRepertoire of function elements at the V\fI .sp 9p .RT .EF '% \fI1\ reference\ point'' .OF '''\fI1\ reference\ point %' .PP The function elements represent input signals which are consumed if a state transition occurs, even if it is a null transition (remain in the same state), and are not longer available to initiate one more state transition. .PP The following repertoire of function elements associated with the activation/deactivation procedures is defined: .RT .LP \(em FE\ 1\ \ (LT\ \(<-\ ET): activation request for the interface at reference point\ T .LP \(em FE\ 2\ \ (LT\ \(ra\ ET): request to start timer T1 within ET layer\ 1 .LP \(em FE\ 3\ \ (LT\ \(ra\ ET): the digital section is activated .LP \(em FE\ 4\ \ (LT\ \(ra\ ET): user\(hynetwork interface at the T\ reference point is activated or loopback is operated .LP \(em FE\ 5\ \ (LT\ \(<-\ ET): deactivation request for the digital section and interface at reference point\ T .LP \(em FE\ 6\ \ (LT\ \(ra\ ET): the digital section is deactivated and the interface at reference point\ T will be or has been deactivated .LP \(em FE\ 7\ \ (LT\ \(ra\ ET): error indication .LP \(em FE\ 8\ \ (LT\ \(<-\ ET): activation request for loopback 2 .LP \(em FE\ 9\ \ (LT\ \(<-\ ET): activation request for loopback 1 .LP \(em FE\ 10\ (LT\ \(<-\ ET): activation request for loopback 1A .LP \(em FE\ 11\ (LT\ \(<-\ ET): request to enter a state where the digital section only is activated .sp 2P .LP 5.4.1.4 \fISpecification of the procedures\fR .sp 1P .RT .sp 1P .LP 5.4.1.4.1\ \ \fIProcedures across the user\(hynetwork interface at reference\fR \fIpoint\ T\fR .sp 9p .RT .PP The digital section supports the procedures across the user\(hynetwork interface at reference point\ T in accordance with Recommendation\ I.430 \(sc\ 6.2. .RT .sp 1P .LP 5.4.1.4.2\ \ \fIDigital section state transition table\fR .sp 9p .RT .PP The state transition table, see Table\ 3/G.960, specifies the procedures. It includes the actions to be taken on various events while in a specific state (see \(sc\ 5.4.1.1 for the definition of the states). In particular, the actions to support the activation/deactivation procedures across the reference point\ T in accordance with Recommendation\ I.430 (sequence of INFOs in compliance with\ I.430). The procedures for loopback operation require further study. .RT .LP .rs .sp 5P .LP .bp .ce \fBH.T. [1T3.960]\fR .ps 9 .vs 11 .nr VS 11 .nr PS 9 .TS center box; cw(342p) . TABLE\ 3/G.960 .T& cw(342p) . { \fBState transition table of digital section (DS state machine)\fR } .TE .TS center box ; cw(24p) | cw(24p) | cw(18p) | cw(24p) | cw(18p) | cw(24p) | cw(18p) | cw(24p) | cw(18p) | cw(48p) . State number DS 1.0 \fB(Note 2)\fR DS 1.1 \fB(Note 2)\fR DS 1.2 (Note 2) DS 1.3 (Note 2) DS 1.5 \fB(Note 2)\fR DS 1.6 \fB(Note 2)\fR DS 1.7 (Note 3) DS 1.8 (Note 3) { DS\(hystates related to loopbacks } .T& cw(24p) | cw(24p) | cw(18p) | cw(24p) | cw(18p) | cw(24p) | cw(18p) | cw(24p) | cw(18p) . INFO SENT INFO 0 INFO 0 INFO 2 INFO 2 INFO 4 INFO 0 INFO 0 INFO 0 _ .T& cw(24p) | cw(24p) | cw(18p) | cw(24p) | cw(18p) | cw(24p) | cw(18p) | cw(24p) | cw(18p) . FE 1 DS 1.1 na na na na DS 1.1 DS 1.1 DS 1.1 _ .T& cw(24p) | cw(24p) | cw(18p) | cw(24p) | cw(18p) | cw(24p) | cw(18p) | cw(24p) | cw(18p) . FE 5 na Start\ T2 DS 1.6 Start\ T2 DS 1.6 Start\ T2 DS 1.6 Start\ T2 DS 1.6 na na na _ .T& lw(24p) | cw(24p) | cw(18p) | cw(24p) | cw(18p) | cw(24p) | cw(18p) | cw(24p) | cw(18p) . Receiving INFO 0 (Note\ 1) \(em \(em \(em \(em FE 7 DS 1.3 \fBFE 7\fR DS 1.7 \(em \fBFE 7\fR DS 1.0 _ .T& lw(24p) | cw(24p) | cw(18p) | cw(24p) | cw(18p) | cw(24p) | cw(18p) | cw(24p) | cw(18p) . Receiving INFO 0 FE 2 DS 1.1 \(em \(em \(em / \(em FE 2\fR DS 1.1 \(em _ .T& lw(24p) | cw(24p) | cw(18p) | cw(24p) | cw(18p) | cw(24p) | cw(18p) | cw(24p) | cw(18p) . Receiving INFO 3 / \(em \(em FE 4\fR DS 1.5 \(em \(em / / _ .T& lw(24p) | cw(24p) | cw(18p) | cw(24p) | cw(18p) | cw(24p) | cw(18p) | cw(24p) | cw(18p) . Lost framing at T (Note\ 1) / \(em \(em \(em FE 7\fR DS 1.3 \(em / / _ .T& lw(24p) | cw(24p) | cw(18p) | cw(24p) | cw(18p) | cw(24p) | cw(18p) | cw(24p) | cw(18p) . Expiry of timer\ T2 \(em \(em \(em \(em \(em \fBFE 7\fR DS 1.7 \(em \fBFE 7\fR DS 1.0 _ .T& lw(24p) | cw(24p) | cw(18p) | cw(24p) | cw(18p) | cw(24p) | cw(18p) | cw(24p) | cw(18p) . Ready to transmit INFO 2 \(em \fBFE 7\fR DS 1.2 \(em \(em \(em \(em \(em \(em _ .T& lw(24p) | cw(24p) | cw(18p) | cw(24p) | cw(18p) | cw(24p) | cw(18p) | cw(24p) | cw(18p) . { Digital section fully activated } \(em \(em FE 3 DS 1.3 \(em \(em \(em \(em \(em _ .T& lw(24p) | cw(24p) | cw(18p) | cw(24p) | cw(18p) | cw(24p) | cw(18p) | cw(24p) | cw(18p) . { Digital section fully deactivated } \(em \(em \(em \(em \(em FE 6\fR DS 1.8 FE 6\fR DS 1.0 \(em _ .TE .nr PS 9 .RT .ad r \fBTableau 3/G.960 [1T3.960] \ \ (\*`a l'italienne), p.\fR .sp 1P .RT .ad b .RT .LP .bp .ce \fBH.T. [2T3.960]\fR .ps 9 .vs 11 .nr VS 11 .nr PS 9 .TS center box; cw(342p) . { TABLE\ 3/G.960\ \fI(cont.)\fR } .T& lw(192p) . .TE .TS center box; cw(24p) | cw(24p) | cw(18p) | cw(24p) | cw(18p) | cw(24p) | cw(18p) | cw(24p) | cw(18p) | cw(48p) . State number DS 1.0 \fB(Note 2)\fR DS 1.1 \fB(Note 2)\fR DS 1.2 (Note 2) DS 1.3 (Note 2) DS 1.5 \fB(Note 2)\fR DS 1.6 \fB(Note 2)\fR DS 1.7 (Note 3) DS 1.8 (Note 3) { DS\(hystates related to loopbacks } INFO sent INFO 0 INFO 0 INFO 2 INFO 2 INFO 4 INFO 0 INFO 0 INFO 0 _ FE 8 _ FE 9 _ FE 10 FE 11 \fBFE 6\fR DS 3.1 \(em \(em Start\ T2 DS 3.6 Start\ T2 DS 3.6 \fBFE 6\fR DS 3.2 \fBFE 6\fR DS 3.1 \fBFE 6\fR DS 3.1 _ .TE .nr PS 9 .RT .ad r \fBRemarques du tableau 3/G.960 [2T3.960], p.\fR .sp 1P .RT .ad b .RT .LP .bp .sp 2P .LP 5.4.2 \fIDescription of the ET layer 1 state transition table\fR .sp 1P .RT .sp 1P .LP 5.4.2.1 \fIET layer 1 states (ET\(hystates)\fR .sp 9p .RT .PP Hereafter are defined the states that the ET layer 1 may enter as a result of: function elements (FEs) received across reference point\ V\d1\u, service primitives received (PH\(hy, MPH\(hyprimitives), or internal events. .PP The ET\(hystates are classified according to the functionality they support as follows: .RT .LP i) ET 1.X states for the support of functionality according to Recommendation\ I.430; .LP ii) ET 2.X states for the support of functionality related to loopbacks (these states complement ET 1.X states); .LP iii) ET 3.X states for the support of functionality related to digital section only activation/deactivation (these states complement ET\ 1.X states). .sp 1P .LP 5.4.2.1.1\ \ State ET 1.0: the access (interface at reference point T and digital section) is in a stable state (deactivated or activated). Timer T1 is not running. .sp 9p .RT .LP 5.4.2.1.2\ \ State ET 1.1: an activation has been initiated to establish a call. Timer\ T1 is running. .LP 5.4.2.1.3\ \ State ET 2.0: the access is in a loopback state. Timer T1 is not running. .LP 5.4.2.1.4\ \ State ET 2.1: a loopback request has been issued. Timer T1 is running. .LP 5.4.2.1.5\ \ State ET 3.0: the access is in a stable state. The digital section only is activated while the interface at the T reference point is deactivated or activated. Timer\ T1 is not running. .LP 5.4.2.1.6\ \ State ET 3.1: an activation has been initiated to establish a call. When the activation of the interface at the T\ reference point was invoked, the digital section was already activated. Timer\ T1 is running. .LP 5.4.2.1.7\ \ State ET 3.2: this is a transitional state which is entered when the digital section only activation has been invoked. Timer\ T1 is running. .sp 1P .LP 5.4.2.2 \fIRepertoire of PH\(hy and MPH\(hyprimitives within ET for the suppport\fR \fIof functions specified in Recommendations\ I.440 and I.441. They are related\fR \fIto call control\fR .sp 9p .RT .PP The repertoire of these primitives is defined in Recommendations I.430 \(sc\ 6.2.1 and\ I.441 \(sc\ 4.1. .PP The MPH\(hyEI primitive used in this Recommendation includes the MPH\(hyEI primitive as defined in Recommendation\ I.430, \(sc\ 6.2.1.5. In addition, it notifies to the system management configuration control an error condition if the activation or loopback operation attempt failed (see \(sc\ 5.4.2.3). .RT .sp 1P .LP 5.4.2.3 \fIRepertoire of MPH\(hyprimitives within ET for the support of\fR \fIfunctions associated with the digital section\fR .sp 9p .RT .PP The primitives below permit the digital section to change between two modes. In the first one, full information transfer capability of the digital section is available whatever the status of the user\(hynetwork interface at reference point\ T is. In the second one, full information transfer capability of the digital section is available only if the user\(hynetwork interface at reference point\ T has to be or is activated. They are related to configuration control. .RT .LP i) MPH\(hyDIGITAl SECTION ACTIVATE\(hyREQUEST (MPH\(hyDSAR) .LP The MPH\(hyDSAR primitive is used to request the digital section to maintain the full information transfer capability disregarding the state of the T\ reference point. The configuration control has to make provision that this primitive is issued only if the access is deactived. .bp .LP ii) MPH\(hyDIGITAL SECTION ACTIVATE\(hyINDICATION (MPH\(hyDSAI) .LP The MPH\(hyDSAI primitive is used to indicate that the digital section is in a mode capable to maintain the full information transfer capability whatever the status of the user\(hynetwork interface at reference point\ T is. .LP iii) MPH\(hyDIGITAL SECTION DEACTIVATE\(hyREQUEST (MPH\(hyDSDR) .LP The MPH\(hyDSDR primitive is used to restore the mode where the status of the digital section is controlled by those primitives (PH\(hyACTIVATE\(hyREQUEST, or MPH\(hyACTIVATE\(hyREQUEST as appropriate, and MPH\(hyDEACTIVATE\(hyREQUEST) which are used for the activation/deactivation of the interface at reference point\ T. This includes the deactivation of the digital section if the interface at reference point\ T has previously been deactivated. The configuration control has to make provision that this primitive is issued only if the interface at reference point\ T is deactivated. .LP iv) MPH\(hyDIGITAL SECTION DEACTIVATE\(hyINDICATION (MPH\(hyDSDI) .LP This primitive supports a confirmed deactivation service. It is issued when the digital section is fully deactivated. Depending on deactivation procedures the interface at the T\ reference point is already or not yet deactivated. .LP v) MPH\(hyERROR\(hyINDICATION (MPH\(hyEI) .LP The MPH\(hyEI primitive is used to notify the system management if the activation or loopback operation attempt failed. .LP vi) MPH\(hyAWAKE\(hyINDICATION (MPH\(hyAWI) .LP This primitive notifies the network side management that the activation of the interface at reference point\ T has been invoked by the user side. It may be used by the ET to assign the resources required to support layer\ 2. .PP The primitives below are associated with maintenance functions based on loopbacks. The activate request primitives include the activation of the digital section and possibly the user\(hynetwork interface at reference point\ T. The establishment of the requested loopback is notified to the requester by means of the MPH\(hyAI primitive. The deactivation of a loopback is invoked by means of the MPH\(hyDSDR primitive, or alternatively the MPH\(hyDR primitive, as appropriate. .LP MPH\(hyL2AR: activation request for loopback 2 .LP MPH\(hyL1AR: activation request for loopback 1 .LP MPH\(hyL1AAR: activation request for loopback 1A .PP The primitives below are used for other test purposes than loopbacks (continuidy test). .sp 9p .RT .LP MPH\(hyAR: activation request of the interface at the T\ reference point and the digital section for continuity test purpose. .LP MPH\(hyAI: activation indication of the interface at the T reference point and of the digital section. .sp 1P .LP 5.4.2.4 \fIET layer 1 state transition table\fR .sp 9p .RT .PP The state transition table, Table 4/G.960, specifies the procedures. It includes the actions to be taken on various events while in a specific state (see \(sc\ 5.4.2.1 for the definition of the states). It specifies the interactions with ET layer\ 2 and system management which are required to support the layer interface procedures in accordance with Recommendation\ I.430 (sequences of PH\(hy and MPH\(hyprimitives in compliance with I.430) and the interactions across the layer interface between ET layer\ 1 and system management for the support of functions associated with the digital section (see \(sc\ 5.4.2.3 for the definition of the related MPH\(hyprimitives). .RT .LP .rs .sp 4P .LP .bp .ce \fBH.T. [1T4.960]\fR .ce TABLE\ 4/G.960 .ce \fBState transition table of ET layer 1\fR .ce \fB(ET layer 1 state machine)\fR .ps 9 .vs 11 .nr VS 11 .nr PS 9 .TS center box; lw(33p) | cw(27p) | cw(27p) | cw(27p) | cw(33p) | cw(27p) | cw(27p) | cw(27p) . State Event ET 1.0 ET 1.1 ET 2.0 ET 2.1 ET 3.0 ET 3.1 ET 3.2 _ .T& cw(33p) | cw(27p) | cw(27p) | cw(27p) | cw(33p) | cw(27p) | cw(27p) | cw(27p) . PH\(hyAR/ MPH\(hyAR Start\ T1 FE 1 ET 1.1 \(em PH\(hyDI \(em PH\(hyDI \(em Start\ T1 FE 1 ET 3.1 \(em Restart\ T1 FE 1 ET 3.1 _ .T& cw(33p) | cw(27p) | cw(27p) | cw(27p) | cw(33p) | cw(27p) | cw(27p) | cw(27p) . MPH\(hyDR PH\(hyDI FE 5 \(em | FE 5 ET 1.0 | PH\(hyDI FE 11 \(em | | _ .T& cw(33p) | cw(27p) | cw(27p) | cw(27p) | cw(33p) | cw(27p) | cw(27p) | cw(27p) . FE 2 Start\ T1 MPH\(hyAWI ET 1.1 (Note 3) MPH\(hyAWI \(em / \(em Start\ T1 MPH\(hyAWI ET 3.1 (Note 3) MPH\(hyAWI \(em { Restart\ T1 MPH\(hyAWI ET 3.1 } _ .T& cw(33p) | cw(27p) | cw(27p) | cw(27p) | cw(33p) | cw(27p) | cw(27p) | cw(27p) . Expiry of timer T1 / MPH\(hyEI ET 1.0 / MPH\(hyEI ET 1.0 / MPH\(hyEI ET 3.0 MPH\(hyEI ET 1.0 _ .T& cw(33p) | cw(27p) | cw(27p) | cw(27p) | cw(33p) | cw(27p) | cw(27p) | cw(27p) . FE 3 (Note 4) MPH\(hyDSAI \(em MPH\(hyDSAI \(em To be specified To be specified (Note 4) MPH\(hyDSAI \(em MPH\(hyDSAI \(em Stop\ T1 MPH\(hyDSAI ET 3.0 _ .T& cw(33p) | cw(27p) | cw(27p) | cw(27p) | cw(33p) | cw(27p) | cw(27p) | cw(27p) . FE 4 (Note 4) MPH\(hyAI \(em { Stop\ T1 PH\(hyAI MPH\(hyAI ET 1.0 } To be specified { Stop\ T1 MPH\(hyAI \fBMPH\(hyAI\fR ET 2.0 } { (Note 4) \fBMPH\(hyAWI\fR \(em } { Stop\ T1 PH\(hyAI MPH\(hyAI ET 3.0 } / _ .T& cw(33p) | cw(27p) | cw(27p) | cw(27p) | cw(33p) | cw(27p) | cw(27p) | cw(27p) . FE 6 MPH\(hyDSDI \(em / To be specified To be specified / / / _ .T& cw(33p) | cw(27p) | cw(27p) | cw(27p) | cw(33p) | cw(27p) | cw(27p) | cw(27p) . FE 7 MPH\(hyDI MPH\(hyEI / To be specified To be specified MPH\(hyDI MPH\(hyEI / / _ .T& cw(33p) | cw(27p) | cw(27p) | cw(27p) | cw(33p) | cw(27p) | cw(27p) | cw(27p) . MPH\(hyL2AR Start\ T1 FE 8 ET 2.1 | | | | | | _ .T& cw(33p) | cw(27p) | cw(27p) | cw(27p) | cw(33p) | cw(27p) | cw(27p) | cw(27p) . MPH\(hyL1AR Start\ T1 FE\ 9 TC 2.1 | | | | | | _ .T& cw(33p) | cw(27p) | cw(27p) | cw(27p) | cw(33p) | cw(27p) | cw(27p) | cw(27p) . MPH\(hyL1AAR Start\ T1 FE\ 10 TC 2.1 | | | | | | _ .T& cw(33p) | cw(27p) | cw(27p) | cw(27p) | cw(33p) | cw(27p) | cw(27p) | cw(27p) . MPH\(hyDSAR (Note 1) Start\ T1 FE\ 11 ET 3.2 { (Note 2) \fBMPH\(hyAI\fR ET 3.1 } | | | | | _ .T& cw(33p) | cw(27p) | cw(27p) | cw(27p) | cw(33p) | cw(27p) | cw(27p) | cw(27p) . MPH\(hyDSDR (Note\ 1) (Note 5) FE\ 5 \(em | FE\ 5 ET 1.0 | FE\ 5 ET 1.0 | { | \(em No state change, no action when event occurs | Impossible event by the definition of the layer 1 service / Impossible event due to internal reasons or peer\(hyto\(hypeer procedures } _ .TE .nr PS 9 .RT .ad r \fBTableau 4/G.960 [1T4.960], p.\fR .sp 1P .RT .ad b .RT .LP .bp .ce \fBH.T. [2T4.960]\fR .ce PH\(hyAI .ce Issue PH\(hyACTIVATE\(hyINDICATION primitive .ce PH\(hyDI .ce Issue PH\(hyDEACTIVATE\(hyINDICATION primitive .ce MPH\(hyAWI .ce Issue MPH\(hyAWAKE\(hyINDICATION primitive .ce \fR .ce MPH\(hyAI .ce Issue MPH\(hyACTIVATE\(hyINDICATION primitive .ce \fR .ce .ce \fR .ce MPH\(hyDI .ce Issue MPH\(hyDEACTIVATE\(hyINDICATION primitive .ce \fR .ce .ce \fR .ce MPH\(hyDSDI .ce Issue MPH\(hyDIGITAL SECTION DEACTIVATE\(hyINDICATION .ce primitive .ce MPH\(hyEI .ce Issue MPH\(hyERROR\(hyINDICATION primitive .ce \fR .ce \fR .ce FE.. .ce Issue function element FE.. across V1 reference point .ce ET ab .ce Enter state ET a.b .ce .LP \fINote\ 1\fR \ \(em\ The primitives MPH\(hyDSAR and MPH\(hyDSDR are allowed only if the T reference point is deactivated. The management has to meet this requirement. .LP \fINote\ 2\fR \ \(em\ This event occurs in the case of a collision between the MPH\(hyDSAR primitive and the MPH\(hyAWI primitive (or the MPH\(hyDSAI primitive, if management ignores the MPH\(hyAWI primitive) at the boundary between ET layer\ 1 and management. This collision has been caused by concurrent invokation of digital section only activation and access activation from the user side. .LP \fINote\ 3\fR \ \(em\ This event occurs in the case of a collision between the function elements FE 1 and FE 2 at reference point\ V1. This collision has been caused by concurrent invokation of an activation of the interface from the user side and network side. .LP \fINote\ 4\fR \ \(em\ These events occur if timer T1 expires concurrently with the completion of a task which the digital section indicates fo ET layer\ 1 by means of the appropriate function element (FE 3 and FE 4). It is a situation caused by excessive delay within the digital section. In some cases it is advantageous to issue the appropriate primitive to notify to management the status of the customer access subsequent to the error indication which would have been conveyed in an MPH\(hyEI primitive. This provides the management with the information to initiate the optimum recovery procedure. .LP \fINote\ 5\fR \ \(em\ This event occurs if timer T1 expired and management invokes a deactivation as a consequence of the receipt of the MPH\(hyEI primitive. In particular this recovery seems to be useful in case of excessive delays (see Note\ 4). .ce \fBH.T. [T5.960]\fR .ce TABLE\ 5/G.960 .ce \fBDefect conditions and consequent actions\fR .ps 9 .vs 11 .nr VS 11 .nr PS 9 .TS center box; cw(36p) | cw(48p) | cw(36p) | cw(54p) sw(54p) , ^ | ^ | c | c | c. Equipment Defect conditions \fB.\fR Consequent actions FII Signal at V 1 Signal at T _ .T& cw(36p) | lw(48p) | cw(36p) | cw(54p) | cw(54p) . LT Excessive error rate (Note 1) Yes FFS FFS .T& cw(36p) | lw(48p) | cw(36p) | cw(54p) | cw(54p) . Line side Loss of signal Yes FE 7 (Note\ 4) INFO (Note\ 5) .T& cw(36p) | lw(48p) | cw(36p) | cw(54p) | cw(54p) . Loss of frame Yes FE 7 (Note\ 4) INFO (Note\ 5) _ .T& cw(36p) | lw(48p) | cw(36p) | cw(54p) | cw(54p) . NT Excessive error rate (Note 1) Yes FFS FFS .T& cw(36p) | lw(48p) | cw(36p) | cw(54p) | cw(54p) . Line side Loss of signal Yes Not applicable INFO (Note\ 5) .T& cw(36p) | lw(48p) | cw(36p) | cw(54p) | cw(54p) . Loss of frame Yes Not applicable INFO (Note\ 5) _ .T& cw(36p) | lw(48p) | cw(36p) | cw(54p) | cw(54p) . NT at T Loss of signal Yes (Note\ 3) FE 7 (Note\ 4) Not applicable (Note\ 3) .T& cw(36p) | lw(48p) | cw(36p) | cw(54p) | cw(54p) . Loss of frame Yes (Note\ 3) FE 7 (Note\ 4) Not applicable _ .T& cw(36p) | lw(48p) | cw(36p) | cw(54p) | cw(54p) . NT Loss of power Yes (Note\ 2) FFS { INFO 0 FFS For further study } .TE .LP \fINote\ 1\fR \ \(em\ If processed in the digital section. .LP \fINote\ 2\fR \ \(em\ Depending on power feed arrangements, optional. .LP \fINote\ 3\fR \ \(em\ Optional. .LP \fINote\ 4\fR \ \(em\ This signal is defined in \(sc\ 5. .LP \fINote\ 5\fR \ \(em\ Whether an existing INFO as defined in Recommendation\ I.430 may be used is for further study. .nr PS 9 .RT .ad r \fBRemarques du tableau 4/G.960 [2T4.960], p.\fR .sp 1P .RT .ad b .RT .LP .sp 3 .sp 1P .LP 5.4.2.5 \fIPrimitive procedures for the support of functions specified\fR \fIin Recommendations I.440 and\ I.441\fR .sp 9p .RT .PP The sequences of PH\(hy and MPH\(hyprimitives which are valid between ET layer\ 1 and ET layer\ 2. and ET layer\ 1 and system management, respectively, for the support of functions specified in Recommendations\ I.440 and\ I.441 and the ET layer\ 1 states as perceived by ET layer\ 2 and system management as a result of primitives transferred between entities are specified in Recommendation\ I.430 \(sc\ 6.2.1.6. .RT .sp 1P .LP 5.4.2.6 \fIPrimitve procedures for the support of functions associated\fR \fIwith the digital section\fR .sp 9p .RT .PP The allowed sequences of MPH\(hyprimitives between ET layer 1 and system management for the support of functions associated with the digital section are specified in the state transition diagram, Figure\ 7/G.960. This state transition diagram defines the ET layer\ 1 states that system management perceives ET layer\ 1 to be in as a result of primitives transferred across the corresponding layer interface. .RT .LP .rs .sp 7P .LP .bp .LP .rs .sp 47P .ad r \fBFigure 7/G.960, p.\fR .sp 1P .RT .ad b .RT .LP .bp .sp 1P .LP 5.5 \fIActivation time\fR .sp 9p .RT .PP For activation from the user side the activation time is measured at the T reference point between the initiation of the sending of INFO\ 1 to the interface at the T\ reference point and the receipt of INFO\ 4 from the digital section. .PP For activation from the network side the activation time is defined between Functional Element\ 1 and Functional Element\ 4 at the V\d1\ureference point. .PP The activation time is specified for a digital section on which a bit error rate lower than the value x (see Note\ 1) can be achieved when activated. .RT .sp 1P .LP 5.5.1 \fIMaximum activation time (see Note\ 2) for activation occuring\fR \fIimmediately after a deactivation (without any intervening loopback or\fR \fIpowering action) (see Note\ 4)\fR : .sp 9p .RT .PP Metallic pair cable transmission system .RT .LP i) without regenerator: 300 ms .LP ii) with regenerator: 600 ms .sp 1P .LP 5.5.2 \fIMaximum activation time (see Note 2) for activation occurring\fR \fIafter the first powering on of a digital section:\fR .sp 9p .RT .LP i) without regenerator: 10 sec .LP ii) with regenerator: 10 sec .PP \fINote\ 1\fR \ \(em\ The exact test conditions are for further study. .PP \fINote\ 2\fR \ \(em\ The specified value for activation time is understood as a 95%\(hyvalue. This means that for 95% of performed activations the activation time must be lower than the specified value. .PP \fINote\ 3\fR \ \(em\ The values take into account the response time of TE for sending INFO\ 3 on receipt of INFO\ 2. .PP \fINote\ 4\fR \ \(em\ Timer T1 being a functional part of the ET it may be physically implemented in the ET. In this case, its value may be adjusted according to the characteristics of the transmission system between the ET and the digital section when it exists (e.g.\ in case of a satellite transmission system a value of 1000\ ms has to be taken into account). .RT .sp 2P .LP \fB6\fR \fBOperation and maintenance\fR .sp 1P .RT .sp 1P .LP 6.1 \fIGeneral\fR .sp 9p .RT .PP This paragraph describes the operation and maintenance functions for the digital section of the ISDN basic rate access. For the time being only functions for a digital transmission system for a metallic line are defined. .PP Operation functions related to activation/deactivation procedure are specified in \(sc\ 5. .PP Further assumptions regarding the system management are given in\fR Annex\ A. .PP The maintenance functions recommended in I.603 provide the capability to maintain the digital section to the level of Network Performance given in \(sc\ 4 of this Recommendation. .PP It must be possible to test and maintain the digital section in accordance with Recommendation\ I.603 regardless of the customer equipment. .PP The main features are: .RT .LP a) control of maintenance and test support facilities; .LP b) monitoring of the functional elements to provide operating and performance information and fault condition indications; .LP c) maintenance communication facility. .sp 2P .LP 6.2 \fIControl facilities\fR .sp 1P .RT .sp 1P .LP 6.2.1 \fILoopbacks\fR .sp 9p .RT .sp 1P .LP 6.2.1.1 Loopback implementation .sp 9p .RT .PP The location and characteristics of loopbacks are defined in Recommendation\ I.603. .bp .RT .sp 1P .LP 6.2.1.2 \fILoopback procedure\fR .sp 9p .RT .PP The loopbacks are controlled by ET system management. .PP A normal call activation request cannot override a request for loopback\ 1, 1a or\ 2. .PP The procedure for loopback operation always starts from the deactivated state of the digital section. .PP One possible sequence is: .RT .LP a) ET generates an operation command for the required loopback; .LP b) ET receives MPH\(hyAI; .LP c) ET performs the test; .LP d) ET generates a release command; .LP e) ET receives MPH\(hyDI. .sp 1P .LP 6.2.2 \fIAuxiliary equipment line\fR \fIswitchover\fR .sp 9p .RT .PP The function provides control of switchovers across the V\d1\ureference point: .RT .LP a) to switch the line from the LT to a line measurement device; .LP b) to switch the line from the normal LT to a standby LT; .LP c) to switch the LT to test NT1 located in the local exchange. .PP This function is optional. The function definition, control options and procedures are for further study. .sp 1P .LP 6.2.3 \fIControl of functions in the NT1\fR .sp 9p .RT .PP This function allows control of specific functions within the NT1 and is for further study. .PP An example of such a function: control of switching between normal and restricted power at the user network interface. .RT .sp 1P .LP 6.2.4 \fIInformation request\fR .sp 9p .RT .PP This function allows the ET to request from the LT, regenerator and NT1 specific status reports. .RT .sp 1P .LP 6.2.5 \fIPower switch on/off to the line\fR .sp 9p .RT .PP This function allows switching of the power to the line, and may be automatically applied upon reception of a power feed failure indication. .RT .sp 1P .LP 6.2.6 \fIContinuity test\fR .sp 9p .RT .PP The continuity test is described in Recommendation I.603. .PP The continuity test is controlled by the ET and is initiated by MPH\(hyAR. System management decides when the test is passed (i.e. on reception of MPH\(hyDSAI or MPH\(hyAI). When the system management receives MPH\(hyEI (expiry T1) the test is considered to be failed. See also Annex\ A to this Recommendation. .RT .sp 2P .LP 6.3 \fIMonitoring\fR .sp 1P .RT .sp 1P .LP 6.3.1 \fIFunctions\fR .sp 9p .RT .PP The following operational conditions are monitored throughout the section: .RT .LP a) the defect conditions; .LP b) the power feed arrangements; .LP c) transmission performance. .sp 1P .LP 6.3.2 \fIImplementation aspects\fR .sp 9p .RT .PP Monitoring capabilities must be provided in the digital section (see Recommendation I.603). The handling and processing of the information is implementation dependent. For example: .RT .LP a) the use of registers/counters in functional groups, the use of explicit commands and responses to establish status reports; .LP b) the transfer of information to the exchange, either when a defect condition occurs or on a regular basis. This information is then processed by entities outside the digital section. .bp .sp 2P .LP 6.3.3 \fIAnomaly and defect conditions and consequent action\fR .sp 1P .RT .sp 1P .LP 6.3.3.1 \fIDefect conditions\fR .sp 9p .RT .PP The following defect conditions are examples: .RT .LP i) excessive error rate; .LP ii) loss of incoming signal; .LP iii) loss of frame alignment; .LP iv) power feed failure. .PP \fINote\fR \ \(em\ One example of an anomaly is a transmission error. .sp 1P .LP 6.3.3.2 \fIConsequent actions\fR .sp 9p .RT .PP Further to the detection of a defect condition appropriate actions should be taken as specified in Table 5/G.960. .PP Defect indication information (FII) is automatically transmitted from the digital section to the\ ET. .RT .ce \fBH.T. [T5.960]\fR .ce TABLE\ 5/G.960 .ce \fBDefect conditions and consequent actions\fR .ps 9 .vs 11 .nr VS 11 .nr PS 9 .TS center box; cw(36p) | cw(48p) | cw(36p) | cw(54p) sw(54p) , ^ | ^ | c | c | c. Equipment Defect conditions \fB.\fR Consequent actions FII Signal at V 1 Signal at T _ .T& cw(36p) | lw(48p) | cw(36p) | cw(54p) | cw(54p) . LT Excessive error rate (Note 1) Yes FFS FFS .T& cw(36p) | lw(48p) | cw(36p) | cw(54p) | cw(54p) . Line side Loss of signal Yes FE 7 (Note\ 4) INFO (Note\ 5) .T& cw(36p) | lw(48p) | cw(36p) | cw(54p) | cw(54p) . Loss of frame Yes FE 7 (Note\ 4) INFO (Note\ 5) _ .T& cw(36p) | lw(48p) | cw(36p) | cw(54p) | cw(54p) . NT Excessive error rate (Note 1) Yes FFS FFS .T& cw(36p) | lw(48p) | cw(36p) | cw(54p) | cw(54p) . Line side Loss of signal Yes Not applicable INFO (Note\ 5) .T& cw(36p) | lw(48p) | cw(36p) | cw(54p) | cw(54p) . Loss of frame Yes Not applicable INFO (Note\ 5) _ .T& cw(36p) | lw(48p) | cw(36p) | cw(54p) | cw(54p) . NT at T Loss of signal Yes (Note\ 3) FE 7 (Note\ 4) Not applicable (Note\ 3) .T& cw(36p) | lw(48p) | cw(36p) | cw(54p) | cw(54p) . Loss of frame Yes (Note\ 3) FE 7 (Note\ 4) Not applicable _ .T& cw(36p) | lw(48p) | cw(36p) | cw(54p) | cw(54p) . NT Loss of power Yes (Note\ 2) FFS { INFO 0 FFS For further study } .TE .LP \fINote\ 1\fR \ \(em\ If processed in the digital section. .LP \fINote\ 2\fR \ \(em\ Depending on power feed arrangements, optional. .LP \fINote\ 3\fR \ \(em\ Optional. .LP \fINote\ 4\fR \ \(em\ This signal is defined in \(sc\ 5. .LP \fINote\ 5\fR \ \(em\ Whether an existing INFO as defined in Recommendation\ I.430 may be used is for further study. .nr PS 9 .RT .ad r \fBTable 5/G.960 [T5.960], p.\fR .sp 1P .RT .ad b .RT .sp 2P .LP 6.3.4 \fIError performance monitoring\fR .sp 1P .RT .sp 1P .LP 6.3.4.1 \fIGeneral\fR .sp 9p .RT .PP Provision has to be made in order to monitor the error performance of the digital section and to report on such performance. .bp .RT .sp 1P .LP 6.3.4.2 \fIError performance parameters\fR .sp 9p .RT .PP The digital section must deliver to the ET the necessary information to allow it to evaluate the error performance parameters defined in Recommendation\ G.821. .RT .sp 1P .LP 6.3.5 \fIStatus report functions\fR .sp 9p .RT .PP Status report functions cover information which relate to the overall operation and performance of the digital section. The information may be transmitted either automatically or under request of ET. .PP Listed below are descriptions of the status report functions: .RT .LP i) \fITransmission errors\fR .LP This information, derived in the digital section, allows the ET to evaluate the transmission error performance. .LP ii) \fILoopback 1 status\fR .LP This information, sent from the LT, gives the status of loopback\ 1. .LP iii) \fILoopback 1A status\fR .LP This information, sent from the regenerator, gives the status of loopback\ 1A. .LP iv) \fILoopback 2 status\fR .LP This information, sent from the NT1, gives the status of loopback\ 2. .LP v) \fIUser network interface power feed status\fR .LP This information indicates the status of the user network interface at T\ reference point power feed, e.g.\ normal or restricted power feed mode. .LP vi) \fIUser network interface power feed fault\fR .LP This information indicates a failure of the normal or restricted power source. .LP This function may be split into two reports. .LP This information is reported on request of the ET. .LP vii) \fIUser network interface power feed overload\fR .LP This information indicates that the power drawn from any source within the NT1 exceeds the maximum power that is available. .LP This information is reported on request of the ET. .LP viii) \fIDefect indication information\fR .LP This information is transmitted automatically under conditions specified in \(sc\ 6.3.3.1. .ce \fBH.T. [T6.960]\fR .ce TABLE\ 6/G.960 .ce \fBStatus report functions\fR .ps 9 .vs 11 .nr VS 11 .nr PS 9 .TS center box; cw(84p) | cw(48p) | cw(60p) . Function Location Mandatory/optional _ .T& lw(84p) | cw(48p) | cw(60p) . Transmission errors LT M .T& lw(84p) | cw(48p) | cw(60p) . \fB.\fR REG. O .T& lw(84p) | cw(48p) | cw(60p) . \fB.\fR NT O .T& lw(84p) | cw(48p) | cw(60p) . Loopback 1 status (Note) LT M .T& lw(84p) | cw(48p) | cw(60p) . Loopback 1A status (Note) REG. M .T& lw(84p) | cw(48p) | cw(60p) . Loopback 2 status (Note) NT1 M .T& lw(84p) | cw(48p) | cw(60p) . { T reference point power feed status } NT1 O .T& lw(84p) | cw(48p) | cw(60p) . { T reference point power feed fault } NT1 O .T& lw(84p) | cw(48p) | cw(60p) . { T reference point power feed overload } NT1 O .T& lw(84p) | cw(48p) | cw(60p) . FII LT M .T& lw(84p) | cw(48p) | cw(60p) . \fB.\fR REG. M .T& lw(84p) | cw(48p) | cw(60p) . \fB.\fR NT M .TE .LP \fINote\fR \ \(em\ The information may be implicit (e.g., activation indication). .nr PS 9 .RT .ad r \fBTableau 6/G.960 [T6.960], p.\fR .sp 1P .RT .ad b .RT .LP .bp .sp 1P .LP 6.3.6 \fISystem dependent status report functions\fR .sp 9p .RT .PP These status reports will be dependent upon the type of digital transmission system used and require further study. .PP Some examples of a particular system are given in Table 7/G.960. .RT .ce \fBH.T. [T7.960]\fR .ce TABLE\ 7/G.960 .ce \fBSystem dependent status report functions\fR .ps 9 .vs 11 .nr VS 11 .nr PS 9 .TS center box; cw(114p) | cw(42p) . Function Location _ .T& lw(114p) | cw(42p) . Line test relay state LT .T& lw(114p) | cw(42p) . LT test relay state LT .T& lw(114p) | cw(42p) . Remote power switch state LT .T& lw(114p) | cw(42p) . Remote power feed LT .T& lw(114p) | cw(42p) . Induced overvoltage on line LT .T& lw(114p) | cw(42p) . Abnormal current condition LT .T& lw(114p) | cw(42p) . Receive eye opening LT REG. NT1 .T& lw(114p) | cw(42p) . { Echo cancellation coefficients } LT REG. NT1 .T& lw(114p) | cw(42p) . Battery test NT _ .TE .nr PS 9 .RT .ad r \fBTable 7/G.960 [T7.960], p.\fR .sp 1P .RT .ad b .RT .sp 2P .LP \fB7\fR \fBControl channel C\fR\(da\fBV\fR\(da\fB1\fR .sp 1P .RT .PP This control channel provides, for each direction of transmission, the capability to transfer the commands, status report information and FII. .PP Although described as a single channel, the control channel may be realized by a number of sub\(hychannels which may use different transport mechanisms (as appropriate to the functions). Even though some of the functions mentioned in \(sc\ 6 have optional status, the C\dV\\d1\uchannel shall have the capability to convey all the control information to allow their implementation. .RT .ce 1000 ANNEX\ A .ce 0 .ce 1000 (to Recommendation G.960) .sp 9p .RT .ce 0 .ce 1000 \fBSYSTEM\ MANAGEMENT\ REQUIREMENTS\fR .sp 1P .RT .ce 0 .LP A.1 \fIIntroduction\fR .sp 1P .RT .PP This Recommendation specifies the required functions of the digital section and the ET layer\ 1. In order to ensure correct operation, it is necessary to take into account the assumptions made about the management functions involved. It is assumed that the structure of the management is as given in CCITT Recommendation\ Q.940. .PP In this Recommendation, distinction is made between ET layer 1 and system management only. Where the term system management is used it corresponds to both system management and layer management as defined in Recommendation\ Q.940. .bp .RT .sp 2P .LP A.2 \fISystem management requirements\fR .sp 1P .RT .sp 1P .LP A.2.1 \fIGeneral\fR .sp 9p .RT .PP System management shall not initiate more than one action at a time towards the ET layer\ 1. An action is delimited by the primitive which is issued by system management and the corresponding primitive which confirms completion of the task. .RT .sp 1P .LP A.2.2 \fIError indications\fR .sp 9p .RT .PP The management entity takes account of the sequence of primitives before and after the reception of MPH\(hyEI. From the sequence of the primitives, the system management may determine the cause of the MPH\(hyEI primitive (e.g.\ unsuccessful activation of the interface, unsuccessfull activation of the access, loss of synchronization or signal at the interface at reference point\ T). .PP Upon the occurence of an error, the ET layer shall notify this event to the system management by means of the primitive MPH\(hyEI. The system management must decide which appropriate actions should be taken (e.g.\ hold or abandon call, initiate MPH\(hyDR or MPH\(hyDSDR). .RT .sp 1P .LP A.2.3 \fILoopback operations\fR .sp 9p .RT .PP The system management should take into account that when the ET layer\ 1 is in loopback operation it does not send any primitives to ET layer\ 2. .PP If a primitive is sent by ET layer 2 to ET layer 1 during loopback operation, it will be ignored by ET layer\ 1. .PP The setting of a loopback is initiated by the system management by issuing a primitive MPH\(hyLxAR where by x\ indicates the type of loopback\ 2, 1 or\ 1A. .PP The setting of the loopbacks 1, 2 and 1A is confirmed to the system management by means of the MPH\(hyAI primitive. The system management should be able to interpret this MPH\(hyAI as a loopback confirmation and not as a normal activation indication by taking into account the sequence of the primitives. .RT .sp 1P .LP A.2.4 \fIContinuity test\fR .sp 9p .RT .PP The continuity test is initiated by the system management using the primitive MPH\(hyAR. The system management must decide when the test is passed (i.e.\ on reception of MPH\(hyDSAI or MPH\(hyAI). If the system management receives MPH\(hyEI (expiry T1) the test is considered to be failed. .PP If the test is passed, the system management should check whether a call establishment has been progressed or if there is a call available before sending MPH\(hyDR. .RT .sp 1P .LP A.2.5 \fIInformation to be sent in the D channel during loopback\fR \fIoperation\fR .sp 9p .RT .PP The information sent in the D channel should not imitate any HDLC pattern. However, it is in the responsibility of the system management to decide to send the required pattern for fault localisation. .RT .sp 1P .LP A.2.6 \fIConfiguration control\fR .sp 9p .RT .PP The system management shall ensure that any action related to configuration control will be issued only when the T\ reference point is deactivated. .RT .ce 1000 ANNEX\ B .ce 0 .ce 1000 (to Recommendation G.960) .sp 9p .RT .ce 0 .ce 1000 \fBVocabulary of terms used in connection with\fR .sp 1P .RT .ce 0 .ce 1000 \fBRecommendations I.430, I.431, G.960 and G.961\fR .ce 0 .LP \fBIntroduction\fR .sp 1P .RT .PP This Annex provides a vocabulary of terms and definitions that are appropriate to layer 1 aspects of the ISDN customer access for basic access and primary rate access. .bp .PP It should be considered in relation to Recommendations\ I.430, I.431, G.960 and\ G.961 since its scope is limited to these Recommendations. It is provided for a clear understanding of these Recommendations and will be reviewed during the next Study Period for alignment with Recommendations produced by other bodies. .PP A small number of terms in this Annex are duplicated in other Recommendations (e.g.\ Recommendation\ I.112 and/or Recommendation\ G.701). References to these are given in parenthesis as an aid to ensuring consistency between the Recommendations in the event of future amendments (e.g.\ \*Qcomplete loopback { .12 } *U). Where the term is defined differently, but the spirit is maintained, the reference is shown as in the following example: \*Qfunctional group { .112,\ 41 } \*U. .PP According to the conventions applied in this Annex any term in common usage, but whose use is deprecated in the sense defined, is shown after the recommended term as in the following example: \*Qline [loop]\*U. .PP Where a truncated term is widely used in an understood context the complete term is quoted following the colloquial form, for example: \*Qmultiplex, digital multiplex equipment\*U. .PP Paragraph\ B.7 contains an alphabetical list of all of the terms contained in this Recommendation. .PP Paragraph B.8 illustrates the general aspects of the terminology. .PP Paragraph B.9 explains the V reference point, V interface, and interface point concept. .RT .sp 2P .LP B.1 \fIGeneral\fR .sp 1P .RT .sp 1P .LP 101 \fBbasic access, basic rate access\fR .sp 9p .RT .PP A user\(hynetwork access arrangement that corresponds to the interface structure composed of two B\(hychannels and one D\(hychannel. The bit rate of the D\(hychannel for this type of access is 16\ kbit/s. .RT .sp 1P .LP 102 \fBprimary rate access\fR .sp 9p .RT .PP A user\(hynetwork access arrangement that corresponds to the primary rates of 1544\ kbit/s and 2048\ kbit/s. The bit rate of the D\(hychannel for this type of access is 64\ kbit/s. The typical primary rate interface structures are as given in Recommendations\ I.412 and I.431. .RT .sp 1P .LP 103 \fBlocal exchange, ISDN local exchange\fR .sp 9p .RT .PP The exchange which, in addition to the switching function, contains the exchange termination for the ISDN customer accesses. .RT .sp 1P .LP 104 \fBline termination (LT)\fR \fB(abbreviated)\fR .sp 9p .RT .PP The functional group containing at least the transmit and receive functions terminating one end of a digital transmission system. .RT .sp 1P .LP 105 \fBexchange termination (ET)\fR \fB(abbreviated)\fR .sp 9p .RT .PP The functional group containing at least the layer 2 and layer 3 network side functions of the I.420 interface at the T reference point. .PP \fINote 1\fR \ \(em\ This may not be true if concentrators or other intelligent equipment are located in the local line distribution network. .PP \fINote 2\fR \ \(em\ The ET is not the switching function. The extent to which the ET supports call control processing and management is not defined. .RT .sp 1P .LP 106 \fBnetwork termination (NT)\fR \fB(abbreviated)\fR .sp 9p .RT .PP The functional group on the network side of a user\(hynetwork interface. .PP \fINote\fR \ \(em\ In Recommendations\ I.430 and\ I.431, \*QNT\*U is used to indicate network terminating layer\ 1 aspects of NT1 and NT2 functional groups. .bp .RT .sp 1P .LP 107 \fBterminal equipment (TE)\fR \fB(abbreviated)\fR .sp 9p .RT .PP The functional group on the user side of a user network interface. .PP \fINote\fR \ \(em\ In Recommendations I.430 and I.431, \*QTE\*U is used to indicate terminal terminating layer\ 1 aspects of TE1, TA and NT2 functional groups. .RT .sp 1P .LP 108 \fBfunctional group\fR { .112, 41 } .sp 9p .RT .PP A set of functions that may be performed by a single equipment. .PP \fINote 1\fR \ \(em\ The transmission medium is not part of any functional group. .PP \fINote 2\fR \ \(em\ Regenerators, multiplexers and concentrators are functional groups which are outside the scope of Recommendation\ I.411. .RT .sp 1P .LP 109 \fBaccess connection element [subscriber access]\fR { .32 } .sp 9p .RT .PP The equipment providing the concatenation of functional groups between and including the exchange termination and the NT1. The term should be qualified by the type of access supported. That is: .RT .LP \(em basic access connection element .LP \(em primary rate access connection element. .sp 1P .LP 110 \fBcustomer equipment [subscriber installation]\fR { .32 } .sp 9p .RT .PP The concatenation of equipment on the user side of the T reference point (i.e.\ TAs, TE2s, TE1s NT2 and associated transmission media). In the case of multiple access, the customer equipment includes all the equipment on the user side of all those accesses comprising the multiple access. .PP \fINote 1\fR \ \(em\ This term should not imply or restrict ownership or responsibility for providing equipment. .PP \fINote 2\fR \ \(em\ The terms \*Quser equipment\*U and \*Qsubscriber equipment\*U are deprecated. .RT .sp 1P .LP 111 \fBISDN customer access [ISDN subscriber access]\fR .sp 9p .RT .PP The equipment providing the concatenation of all functional groups relevant to an individual or group of related access connection elements (i.e.\ customer equipment and access connection element). .PP \fINote\fR \ \(em\ This term should not imply or restrict ownership or responsibility for providing equipment. .RT .sp 1P .LP 112 \fBdirect access, direct access connection element\fR .sp 9p .RT .PP A specific access connection element in which the basic access digital section or primary rate access digital section is directly connected to the exchange termination at a V\d1\uor \d3\ureference point respectively. .RT .sp 1P .LP 113 \fBremote access, remote access connection element\fR .sp 9p .RT .PP A specific access connection element in which the digital section is not directly connected to the exchange termination but is connected through a multiplexer or concentrator. .RT .sp 1P .LP 114 \fBreference point\fR { .112, 42 } .sp 9p .RT .PP A conceptual point at the conjunction of two non\(hyoverlapping functional groups. .PP \fINote\fR \ \(em\ Each reference point is assigned a prefix letter, for example: T\ reference point. .bp .RT .sp 1P .LP 115 \fBinterface, physical interface\fR { .112, 408; G.701, 100 } .sp 9p .RT .PP The common boundary between physical equipment. .RT .sp 1P .LP 116 \fBuser network interface [customer network interface]\fR { .112, 40 } .sp 9p .RT .PP An interface, at which the access protocols apply, and which is located at the S\ or T\ reference point. .RT .sp 1P .LP 117 \fBV interface\fR .sp 9p .RT .PP A digital interface which usually coincides with the V reference point. .PP \fINote\ 1\fR \ \(em\ A specific V interface is denoted by a suffix number. .PP \fINote\ 2\fR \ \(em\ The V interfaces are internal network interfaces. .RT .sp 1P .LP 118 \fBV\fR\(da\fB1 reference point\fR .sp 9p .RT .PP A V reference point at the network side of a basic access digital section for the provision of a single basic access. .PP \fINote\fR \ \(em\ The V\d1\uinterface is a functional boundary between the exchange termination and the line termination and may or may not exist as a physical interface. The V\d1\uinterface structure is comprised of two B\(hychannels, one D\(hychannel, and a C\dv\\d1\u\(hychannel. .RT .sp 1P .LP 119 \fBV\fR\(da\fB2 reference point\fR .sp 9p .RT .PP A V reference point at the network side of a concentrator for the provision of a number of basic and/or primary rate accesses. .RT .sp 1P .LP 120 \fBV\fR\(da\fB3 reference point\fR .sp 9p .RT .PP A V reference point at the network side of a primary rate access digital section for the provision of a single primary rate access. .RT .sp 1P .LP 121 \fBV\fR\(da\fB4 reference point\fR .sp 9p .RT .PP A V reference point at the network side of a multiplexer supporting several basic access digital sections. .RT .sp 2P .LP B.2 \fIDigital transmission\fR .sp 1P .RT .sp 1P .LP 201 \fBDigital link, digital transmission link\fR { .112, 302; G.701, 300 } .sp 9p .RT .PP The whole of the means of digital transmission of a digital signal of specified rate between specified reference points. .PP \fINote\fR \ \(em\ A digital link comprises one or more digital sections and may include either a multiplexer or concentrator, but not switching. .RT .sp 1P .LP 202 \fBdigital access link\fR .sp 9p .RT .PP A digital link between the T reference point and the V reference point in the case of remote access only. .RT .sp 1P .LP 203 \fBdigital section [section]\fR { .701, 300 } .sp 9p .RT .PP The whole of the means of digital transmission of a digital signal of specified rate between two consecutive reference points. The term should be qualified by the type of access supported, or by a prefix denoting the V\ interface at the digital section boundaries. For example: .RT .LP \(em basic access digital section; .LP \(em primary rate access digital section; .LP \(em V\dx\udigital section. .bp .sp 1P .LP 204 \fBdigital section boundaries\fR .sp 9p .RT .PP The reference points at the near and far ends of the digital section. .RT .sp 1P .LP 205 \fBdigital system, digital transmission system [system]\fR { .701, 301 } .sp 9p .RT .PP A specific means of providing a digital section. .PP \fINote\fR \ \(em\ For a specific type of system this term may be qualified by the insertion of the name of the transmission medium employed by that specific system. Some examples are: .RT .LP \(em digital line transmission system; .LP \(em digital radio system; .LP \(em digital optical transmission system. .sp 1P .LP 206 \fBtransmission method\fR .sp 9p .RT .PP The technique by which the transmission system transmits and receives signals via the transmission medium. .RT .sp 1P .LP 207 \fBecho cancellation\fR .sp 9p .RT .PP A transmission method used in digital transmission systems in which bi\(hydirectional transmission occurs simultaneously on the same line and in the same frequency band. An echo canceller is required to attenuate the echo of the near\(hyend transmission. .RT .sp 1P .LP 208 \fBtime compression multiplex [burst mode]\fR .sp 9p .RT .PP A transmission method used in digital transmission systems in which bi\(hydirectional transmission occurs in non\(hyoverlapping uni\(hydirectional bursts. .RT .sp 1P .LP 209 \fBmultiplex, digital multiplex equipment\fR { .701, 401 } .sp 9p .RT .PP The combination of a digital multiplexer and a digital demultiplexer at the same location, operating in opposite directions of transmission. .RT .sp 1P .LP 210 \fBstatic multiplex [fixed multiplex]\fR .sp 9p .RT .PP A multiplex where each tributary channel is assigned to one or more main\(hystream time\(hyslots and the assignment is fixed. .RT .sp 1P .LP 211 \fBdynamic multiplex [statistical multiplex]\fR .sp 9p .RT .PP A multiplex where signalling information of some or all tributary D\(hychannels is assigned to a lesser number of main\(hystream time\(hyslots on a statistical basis, but the assignment of other channels is fixed. .RT .sp 1P .LP 212 \fBconcentrator, digital concentrator\fR .sp 9p .RT .PP Equipment containing the means to combine, in one direction, a number of basic accesses, and/or primary rate accesses into a lesser number of time\(hyslots by omitting the idle channels and/or redundancy, and to perform the corresponding separation in the contra\(hydirection. .RT .sp 2P .LP B.3 \fISignalling\fR .sp 1P .RT .sp 1P .LP 301 \fBINFO\fR .sp 9p .RT .PP A defined layer 1 signal with specified meaning and coding at a basic access user\(hynetwork interface. .bp .RT .sp 1P .LP 302 \fBSIG\fR .sp 9p .RT .PP A signal representing an exchange of layer 1 information between line terminations of a digital transmission system for basic access. .RT .sp 1P .LP 303 \fBfunction elements (FEs)\fR \fB(abbreviated)\fR .sp 9p .RT .PP A signal representing a functional exchange of layer 1 information at the V\d1\uinterface. .RT .sp 1P .LP 304 \fBcontrol channel; C\(hychannel [service channel]\fR .sp 9p .RT .PP Additional dedicated transmission capability provided at a reference point or interface, or transported by a digital transmission system, to support the execution of management functions. .PP \fINote\fR \ \(em\ The control channel at a specific reference point, interface or type of transmission system is denoted by an appropriate suffix. For example: .RT .LP \(em C\dv\\d1\u: channel \(em the control channel at the V\d1\uinterface .LP \(em C\dL\u: channel \(em the control channel at the line. .sp 2P .LP B.4 \fIActivation/deactivation\fR .sp 1P .RT .sp 1P .LP 401 \fBdeactivation\fR .sp 9p .RT .PP A function which places a system, or part of a system, into a non\(hyoperating or partially operating mode where the power consumption of the system may be decreased (low power consumption mode). .RT .sp 1P .LP 402 \fBactivation\fR .sp 9p .RT .PP A function which places a system, or part of a system, which may have been in a low power consumption mode during deactivation, into its fully operating mode. .RT .sp 1P .LP 403 \fBpermanent activation\fR .sp 9p .RT .PP Activation of a system, or part of a system, that will not be deactivated even when it is not required to be fully operating. .RT .sp 1P .LP 404 \fBline activation\fR .sp 9p .RT .PP The function which requires the digital line transmission system to be activated but which may also activate the user\(hynetwork interface. .RT .sp 1P .LP 405 \fBline\(hyonly activation\fR .sp 9p .RT .PP The function which requires the activation of only the digital line transmission system and does not activate the user\(hynetwork interface. .RT .sp 1P .LP 406 \fBone\(hystep activation\fR .sp 9p .RT .PP A type of activation which invokes a sequence of actions to activate the digital line transmission system and user\(hynetwork interface from a single command. .RT .sp 1P .LP 407 \fBtwo\(hystep activation\fR .sp 9p .RT .PP A type of activation which is initiated by one command to invoke a sequence of actions to activate the digital line transmission system and continued by a second command to invoke a sequence of actions to activate the user\(hynetwork interface. .bp .RT .sp 1P .LP 408 \fBone\(hystep deactivation\fR .sp 9p .RT .PP Deactivation of the digital line transmission system and user\(hynetwork interface invoked by a single command. .RT .sp 1P .LP 409 \fBuser\(hynetwork interface only deactivation\fR .sp 9p .RT .PP Deactivation of the user\(hynetwork interface which does not deactivate the digital line transmission system. .RT .sp 2P .LP B.5 \fILoopbacks\fR .sp 1P .RT .sp 1P .LP 501 \fBloopback, digital loopback\fR { .12 } \fB[test loop]\fR { .112 } .sp 9p .RT .PP A mechanism incorporated into a piece of equipment whereby a bi\(hydirectional communication path may be connected back on itself so that some or all of the information contained in the bit stream sent on the transmit path is returned on the receive path. .RT .sp 1P .LP 502 \fBloopback type\fR .sp 9p .RT .PP The characteristic of a loopback which specifies the relationship between information entering the loopback and the information leaving the loopback in the contra\(hydirection. .RT .sp 1P .LP 503 \fBcomplete loopback\fR { .12 } .sp 9p .RT .PP A physical layer 1 mechanism which operates on the full bit stream. At the loopback point, the receive bit stream shall be transmitted back towards the transmitting station without modification. .PP \fINote\fR \ \(em\ The use of the term \*Qcomplete loopback\*U is not related to implementation since such a loopback may be provided by means of active logic elements or controlled unbalance of a hybrid transformer,\ etc. At the control point only the information channels may be available. .RT .sp 1P .LP 504 \fBpartial loopback\fR { .12 } \fB[echoing loopback]\fR .sp 9p .RT .PP A physical layer 1 mechanism which operates on one or more specified channels multiplexed within the full bit stream. At the loopback point, the received bit stream associated with the specified channel(s) shall be transmitted back towards the transmitting station without modification. .RT .sp 1P .LP 505 \fBlogical loopback\fR { .12 } .sp 9p .RT .PP A loopback which acts selectively on certain information within a specified channel or channels and may result in some specified modification of the looped information. Logical loopbacks may be defined to apply at any layer, depending on the detailed maintenance procedures specified. .RT .sp 1P .LP 506 \fBloopback point\fR { .12 } .sp 9p .RT .PP The precise location of the loopback. .RT .sp 1P .LP 507 \fBloopback control mechanism [control mechanism]\fR { .12 } .sp 9p .RT .PP The means by which the loopback is operated and released from the loopback control point. .RT .sp 1P .LP 508 \fBloopback control point [control point]\fR { .12 } .sp 9p .RT .PP The point which has the ability to directly control loopbacks. The loopback control point may receive requests for loopback operation from several loopback requesting points. .RT .sp 1P .LP 509 \fBloopback requesting point\fR { .12 } .sp 9p .RT .PP The point which requests the loopback control point to operate loopbacks. .bp .RT .sp 1P .LP 510 \fBloopback application\fR { .12 } .sp 9p .RT .PP The maintenance phase for which the loopback operation is used. .RT .sp 1P .LP 511 \fBforward signal\fR .sp 9p .RT .PP The signal transmitted beyond the loopback point. .PP \fINote\fR \ \(em\ The forward signal may be a defined signal or unspecified. .RT .sp 1P .LP 512 \fBloopback test pattern\fR { .12 } .sp 9p .RT .PP The information transmitted during the operation of the loopback in the channel or channels which are to be redirected by the loopback. .RT .sp 1P .LP 513 \fBtransparent loopback\fR { .12 } .sp 9p .RT .PP A transparent loopback is one in which the signal transmitted beyond the loopback point (the forward signal) when the loopback is activated, is the same as the received signal at the loopback point. See Figure B\(hy1/G.960. .RT .LP .rs .sp 12P .ad r \fBFigure B\(hy1/G.960, p.\fR .sp 1P .RT .ad b .RT .sp 1P .LP 514 \fBnon\(hytransparent loopback\fR { .12 } .sp 9p .RT .PP A non\(hytransparent loopback is one in which the signal transmitted beyond the loopback point (the forward signal) when the loopback is activated is not the same as the received signal at the loopback point. The forward signal may be a defined signal or unspecified. See Figure\ B\(hy2/G.960. .RT .LP .rs .sp 13P .ad r \fBFigure B\(hy2/G.960, p.\fR .sp 1P .RT .ad b .RT .LP .bp .sp 2P .LP B.6 \fIlocal line distribution network\fR .sp 1P .RT .sp 1P .LP 601 \fBlocal line distribution network\fR .sp 9p .RT .PP A network of cables and wires which are currently installed between a local exchange and customer premises. .RT .sp 1P .LP 602 \fBtwisted pair\fR .sp 9p .RT .PP A line or part of a line which has each (insulated) conductor twisted around the other to reduce the effect of induction from stray electromagnetic and/or electrostatic fields. .PP \fINote\fR \ \(em\ This definition also applies to twisted quad except that two pairs are twisted together. .RT .sp 1P .LP 603 \fBexchange cable\fR .sp 9p .RT .PP A cable forming part of the local line distribution network, used in the local exchange between the line termination and main distribution frame. .RT .sp 1P .LP 604 \fBmain cable\fR .sp 9p .RT .PP A cable used in the local line distribution network between the main distribution frame and a cross connection point. .RT .sp 1P .LP 605 \fBdistribution cable\fR .sp 9p .RT .PP A cable used in the local line distribution network between the cross connection point and a distribution point. .RT .sp 1P .LP 606 \fBinstallation cable [subscriber cable]\fR .sp 9p .RT .PP A cable or single pair of metallic wires used in the local line distribution point and the customer premises. .RT .sp 1P .LP 607 \fBbridged tap\fR .sp 9p .RT .PP A length of unused open circuit line that is \*QT\*Ued to the customer line to provide flexibility in the local line distribution network. .PP \fINote\fR \ \(em\ Bridged taps are not used in all local line distribution networks. .RT .sp 1P .LP 608 \fBopen wire\fR .sp 9p .RT .PP A pair of suspended and often uninsulated metallic wires which run parallel to each other. .PP \fINote\fR \ \(em\ Overhead installation cables in common use between distribution poles and customer premises are not open wires. .RT .sp 1P .LP 609 \fBloading coil\fR .sp 9p .RT .PP A device used to modify the electric characteristics of a line to give relatively constant attenuation over the voice\(hyfrequency range, but which gives relatively high attenuation beyond that range. .bp .RT .sp 1P .LP 610 \fBcrosstalk\fR .sp 9p .RT .PP A phenomenon by which an unwanted signal is introduced into a line through coupling to one or more other lines. .RT .sp 1P .LP 611 \fBintrasystem crosstalk\fR .sp 9p .RT .PP Crosstalk between lines sharing the same cable on which the same type of transmission system is used on each line. .RT .sp 1P .LP 612 \fBintersystem crosstalk\fR .sp 9p .RT .PP Crosstalk between lines sharing the same cable and on which different types of transmission systems are used on each line. .RT .sp 1P .LP 613 \fBnear\(hyend crosstalk (NEXT)\fR \fB(abbreviated)\fR .sp 9p .RT .PP Crosstalk where the coupling is occurring at or near to the transmitter. .RT .sp 1P .LP 614 \fBfar\(hyend crosstalk (FEXT)\fR \fB(abbreviated)\fR .sp 9p .RT .PP Crosstalk where the coupling is occurring at or near to the end of the line furthest from the transmitter. .RT .sp 1P .LP 615 \fBline [loop]\fR .sp 9p .RT .PP The transmission medium between line terminations. The term may be qualified by the type of medium used, for example: .RT .LP \(em metallic\ line: a pair of metallic (usually copper) wires, .LP \(em optical\ line: one optical fibre (bi\(hydirectional transmission), or one pair of fibres (uni\(hydirectional transmission). .sp 1P .LP 616 \fBlocal line [subscriber line]\fR .sp 9p .RT .PP An individual line which is continuous between the line termination (LT) and the customer premises, passing through the exchange, main, distribution and installation cables. .RT .sp 1P .LP 617 \fBdigital local line\fR .sp 9p .RT .PP A local line which is used by a digital transmission system. .PP \fINote\fR \ \(em\ Regenerators are not part of the line but may be inserted between two line lengths. .bp .RT .sp 2P .LP B.7 \fIAlphabetical list of terms contained in this Annex\fR .sp 1P .RT .sp 1P .LP 109 access connection element .sp 9p .RT .LP \fR 402 activation .LP 101 basic access .LP 101 basic rate access .LP 607 bridged tap .LP 208 [burst mode] .LP 304 C\(hychannel .LP 503 complete loopback .LP 212 concentrator .LP 304 control channel .LP 507 [control mechanism] .LP 508 [control point] .LP 610 crosstalk .LP 110 customer equipment .LP 116 [customer network interface] .LP 401 deactivation .LP 202 digital access link .LP 212 digital concentrator .LP 201 digital link .LP 617 digital local line .LP 501 digital loopback .LP 209 digital multiplex equipment .LP 203 digital section .LP 204 digital section boundaries .LP 205 digital system .LP 201 digital transmission link .LP 205 digital transmission system .LP 112 direct access .LP 112 direct access connection element .LP 605 distribution cable .LP 211 dynamic multiplex .LP 207 echo cancellation .LP 504 [echoing loopback] .LP 603 exchange cable .LP 105 exchange termination (ET) (abbreviated) .LP 614 far\(hyend crosstalk (FEXT) (abbreviated) .LP 210 [fixed multiplex] .LP 511 forward signal .LP 303 function element [FEs) (abbreviated) .LP 108 functional group .LP 301 INFO .LP 606 installation cable .LP 115 interface .LP 612 intersystem crosstalk .LP 611 intrasystem crosstalk .LP 111 ISDN customer access .LP 103 ISDN local exchange .LP 111 [ISDN subscriber access] .LP 615 line .LP 404 line activation .LP 405 line\(hyonly activation .LP 104 line termination (LT) (abbreviated) .LP 609 loading coil .LP 103 local exchange .LP 616 local line .LP 601 local line distribution network .LP 505 logical loopback .LP 615 [loop] .LP 501 loopback .LP 510 loopback application .LP 507 loopback control mechanism .LP 508 loopback control point .LP 506 loopback point .LP 509 loopback requesting point .LP 512 loopback test pattern .LP 502 loopback type .LP 604 main cable .LP 209 multiplex .LP 613 near\(hyend crosstalk (NEXT) (abbreviated) .LP 106 network termination (NT) (abbreviated) .LP 514 non\(hytransparent loopback .LP 406 one\(hystep activation .LP 408 one\(hystep deactivation .LP 608 open wire .LP 504 partial loopback .LP 403 permanent activation .LP 115 physical interface .LP 102 primary rate access .LP 114 reference point .LP 113 remote access .LP 113 remote access connection element .LP 203 [section] .LP 304 [service channel] .LP 302 SIG .LP 210 static multiplex .LP 211 [statistical multiplex] .LP 109 [subscriber access] .LP 606 [subscriber cable] .LP 110 [subscriber installation] .LP 616 [subscriber line] .LP 205 [system] .LP 107 terminal equipment; (TE) (abbreviated) .LP 208 time compression multiplex .LP 206 transmission method .LP 513 transparent loopback .LP 602 twisted pair .LP 407 two\(hystep activation .LP 116 user\(hynetwork interface .LP 409 user\(hynetwork interface only deactivation .LP 117 V interface .LP 118 V\d1\ureference point .LP 119 V\d2\ureference point .LP 120 V\d3\ureference point .LP 121 V\d4\ureference point .LP .bp .sp 2P .LP B.8 \fIIllustration of the general aspects of the terminology ISDN\fR \fIcustomer access\fR .sp 1P .RT .LP .rs .sp 47P .ad r \fBFigure B\(hy3/G.960, p.\fR .sp 1P .RT .ad b .RT .LP .bp .sp 2P .LP B.9 \fIClarification of the V reference point, V interface,\fR \fIand interface point concept\fR .sp 1P .RT .PP B.9.1 The V\d1\ureference point and the V\d3\ureference point are always on the network side of the line termination and are applicable to individual (low order) accesses. .sp 9p .RT .PP A reference point, when physically realized by an interface, requires the specification of at least two interface points. See Figure\ B\(hy4/G.960. .LP .rs .sp 10P .ad r \fBFigure B\(hy4/G.960, p.\fR .sp 1P .RT .ad b .RT .sp 1P .LP B.9.2 \fIInterface point\fR .sp 9p .RT .PP One of at least two physical locations associated with an interface. The interface points mark the end of the transmission medium which supports the interface and may be the location of connectors (if used). .PP The reach of any interface may be extended by the use of a transmission system, providing that the transmission system is transparent in regards to the functions transported by the interface. In such a case, two further interface points would be required. See Figure\ B\(hy5/G.960. .RT .LP .rs .sp 10P .ad r \fBFigure B\(hy5/G.960, p.\fR .sp 1P .RT .ad b .RT .PP B.9.3 A group of individual accesses may be multiplexed or concentrated together to comprise a higher order access (i.e.\ V\d2\uor \d6\ufor basic access higher order interfaces). .PP There is only one V reference point at which the V interfaces may be implemented (between LT and ET). See Figure\ B\(hy6/G.960. .PP This approach aligns with the use of I\dB\uand I\dA\uinterface points in Recommendations\ I.430 and I.431. .RT .LP \(em with the modelling technique used so far; .LP \(em with the terminology used so far; .LP \(em with the fact that an S or T reference point may support a range of interfaces (Recommendations\ I.430/I.431); .LP \(em does not contradict Recommendation Q.512. .bp .LP .rs .sp 20P .ad r \fBFigure B\(hy6/G.960, p.22\fR .sp 1P .RT .ad b .RT .LP .rs .sp 29P .LP \fBMONTAGE:\ \fR REC. G.961 A LA FIN DE CETTE PAGE .sp 1P .RT .LP .bp